Archives

Application Information

The TPMC376 is a conduction cooled single-width 32 bit

PMC module offering 4 channels of high performance

RS232/RS422/RS485 programmable asynchronous serial

interface with P14 I/O.

The serial channels can be individually programmed to

operate as RS232. RS422 or RS485 full duplex / half

duplex interface. In addition programmable termination is

provided for the RS422/RS485 interfaces. After power-up

all serial I/O lines are in a high impedance state.

Each RS232 channel supports RxD, TxD, RTS, CTS and

GND. RS422 and RS485 full duplex support a four wire

interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485

half duplex supports a two wire interface (DX+, DX-) plus

ground (GND).

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422/RS485 channels.

The UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC376 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D158 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interface

 Octal UART: Exar XR17D158

 Programmable Interfaces:

 RS232

 RS422

 RS485 full duplex

 RS485 half duplex

 Programmable Termination for RS422/RS485

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422/RS485 FD channel; D+/- and GND for each

RS485 HD channel.

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422/RS485: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV )

 Operating temperature -40°C to +85°C

Application Information

The TPMC375 is a conduction cooled single-width 32 bit

PMC module offering 8 channels of high performance

RS232/RS422/RS485 programmable asynchronous serial

interface with P14 I/O.

The serial channels can be individually programmed to

operate as RS232. RS422 or RS485 full duplex/half

duplex interface. In addition programmable termination is

provided for the RS422/RS485 interfaces. After power-up

all serial I/O lines are in a high impedance state.

Each RS232 channel supports RxD, TxD, RTS, CTS and

GND. RS422 and RS485 full duplex support a four wire

interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485

half duplex supports a two wire interface (DX+, DX-) plus

ground (GND).

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422/RS485 channels.

The UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC375 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D154 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interface

 Quad UART: Exar XR17D154

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422 channel. One channel offers extended support

(full modem or RTS+/- and CTS+/-)

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV)

 Operating temperature -40°C to +85°C

Application Information

The TPMC372 is a conduction cooled single-width 32 bit

PMC module and offers 4 channels of high performance

asynchronous serial interface.

Three different standard modules are available: The

TPMC372-10xR provides 4 RS232 interfaces. The

TPMC372-11xR provides 4 RS422 interfaces. The

TPMC372-12xR provides 2 RS232 and 2 RS422 interfaces.

Other configurations are available as factory build option

on a per channel base.

All modules offer P14 I/O. Each RS232 channel supports

RxD, TxD, RTS, CTS and GND. Each RS422 channel

supports RxD+/-, TxD+/- and GND. One channel of the

TPMC372-10xR/-12xR offers full modem support (TxD,

RxD, CTS, RTS, DSR, DTR, CD, RI and GND) for RS232.

One channel of the TPMC372-11xR supports RxD+/-,

TxD+/-, RTS+/-, CTS+/- and GND for RS422.

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422 channels. The

UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC372 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction cooled single-width 32 bit PMC module

conforming to IEEE P1386.1. no front panel

 Target Chip: XR17D158 (Exar)

 PCI 2.3 compliant interface

 PCI I/O signaling voltage 5V and 3.3V

 Board size: 143.75 mm x 74 mm

 Asynchronous serial interfaces

 Octal UART: Exar XR17D158

 Support of RxD, TxD, RTS, CTS and GND for each

RS232 channel; RxD+/-, TxD+/- and GND for each

RS422 channel. Two channels offer extended support

(full modem or RTS+/- and CTS+/-)

 Programmable baud rates:

RS232: up to 921.6 kbps

RS422: up to 5.5296 Mbps

 64 byte transmit FIFO per channel

 64 byte receive FIFO per channel

 Readable FIFO levels

 Global Interrupt Source Register

 General Purpose 16 bit Timer/Counter

 ESD protected transceiver (up to ± 15KV )

 Operating temperature -40°C to +85°C

Application Information

The TPMC371 is a conduction cooled single-width 32 bit

PMC module and offers 8 channels of high performance

asynchronous serial interface.

Three different standard modules are available: The

TPMC371-10xR provides 8 RS232 interfaces. The

TPMC371-11xR provides 8 RS422 interfaces. The

TPMC371-12xR provides 4 RS232 and 4 RS422 interfaces.

Other configurations are available as factory build option

on a per channel base.

All modules offer P14 I/O. Each RS232 channel supports

RxD, TxD, RTS, CTS and GND. Each RS422 channel

supports RxD+/-, TxD+/- and GND. Two channels of the

TPMC371-10xR/-12xR offer full modem support (TxD,

RxD, CTS, RTS, DSR, DTR, CD, RI and GND) for RS232.

Two channels of the TPMC371-11xR support RxD+/-,

TxD+/-, RTS+/-, CTS+/- and GND for RS422.

Each channel has 64 byte transmit and receive FIFOs to

significantly reduce the overhead required to provide data

to and get data from the transmitters and receivers. The

FIFO trigger levels are programmable and the baud rate is

individually programmable up to 921.6 kbps for RS232

channels and 5.5296 Mbps for RS422 channels. The

UART offers readable FIFO levels.

All channels generate interrupts on PCI interrupt INTA. For

fast interrupt source detection the UART provides a

special Global Interrupt Source Register.

All serial channels use ESD protected transceivers. ESD

protection is up to ±15KV.

The TPMC371 can operate with 3.3V and 5.0V PCI I/O

signaling voltage.

Software Support (TDRV002-SW-xx) for different

operating systems is available.

Technical Information

 Conduction Cooled single-width 32 bit PMC module

conforming to IEEE P1386.1

 PCI 2.1 compliant master/slave interface

 3.3V and 5V PCI Signaling Voltage

 Board size: 143.75 mm x 74 mm

 Four high speed asynchronous/synchronous (HDLC)

serial interfaces

 Support of RxD, TxD, RxC, TxC, RTS, CTS, CD and

GND on rear connector P14

 Physical interface (individually programmable per

channel):

EIA-232. EIA-422. EIA-449. EIA-530. EIA-530A, V.35.

V.36 and X.21

 Maximum data rate: 10 Mbit/s (synchronous),

2 Mbit/s (asynchronous), internally or externally

provided clock

 EIA-232: up to 115.2 kbit/s

Temperature range: -40°C to +85°C

A 14.7456 MHz oscillator provides standard asynchronous

baud rates. An additional 24 MHz oscillator is provided for

other baud rates. A 10 MHz oscillator is used for the

synchronous baud rate of 10 Mbit/s.

Each channel also provides various interrupt sources,

generated on INTA. The interrupt sources can be enabled

or disabled individually.

Multiprotocol transceivers are used for the line interface.

The physical interface is selectable by software, individually

for each channel as EIA-232. EIA-422. EIA-449. EIA-530.

EIA-530A, V.35. V.36 or X.21.

The following signals are provided by the TPMC363  for

each channel at the front and rear-I/O connectors:

Receive Data (RxD +/-), Transmit Data (TxD +/-), Receive

Clock (RxC +/-), Transmit Clock (TxC +/-), Ready-To-Send

(RTS +/-), Clear-To-Send (CTS +/-), Carrier-Detect (CD +/

) and GND.

The TPMC363 provides rear panel I/O via P14.

Software Support (TDRV009-SW-xx) for different operating

systems is available.

Application Information

The TPMC363 is a conduction cooled single-width 32 bit

PMC with four high speed serial data communication

channels.

The TPMC363 is the successor of the discontinued

TPMC362. providing similar functionality and full connector

and pin-out compatibility.

The serial communication controller is implemented in

FPGA logic, along with the bus master capable PCI

interface, guaranteeing long term availability and having the

option to implement additional functions in the future.

Each channel provides dedicated receive and transmit

FIFOs for high data throughput.

Data transfer on the PCI bus is handled via TPMC363

initiated DMA cycles with minimum host/CPU intervention.

Several serial communication protocols are supported by

each channel, such as asynchronous, isochronous,

synchronous and HDLC mode.