Archives

The IC695ALG412 is a strain gauge input module that is part of the PACSystem RX3i analog input module. The module features twelve (12) isolated differential input channels and is compatible with millivolt signals (e.g., ±150mV or ±50mV) and thermocouple instruments (e.g., J, K, T, E, R, S, B, N, or C types). The module can be used for direct connection to strain gauges and for temperature applications without the need for transmitters, signal conditioners, and other equipment.

The module occupies a single slot on the backplane and connects directly to the RX3i general purpose backplane only and directly to the PCI bus. The module also comes with internal diagnostics such as open circuit, short circuit, positive/negative rate of change, high, high-to-high, low and low-to-low channel diagnostics. In addition, the module has built-in interchannel isolation and is rated for continuous voltages of 250VAC; 1500VAC for 1 minute; 2550VDC for 1 second with an input impedance of >=500k ohms. The module offers a 10 dB improvement in noise rejection.

The module features sigma-delta analog-to-digital converter type circuitry with 32-bit IEEE floating point or 16-bit integer resolution (in 32-bit fields), conversion times from 15 ms @ 28 Hz to 120 ms @ 2.3 Hz, and an input data format and accuracy of ± 59163.25% of the voltage at 0 °C sp+GC+GB1GD59+GC1 an. ± 0.25% of range over the entire temperature range.

The module requires the use of a removable terminal block (RTB) such as IC694TBBx32. IC694TBSx32. or IC694TBC032. It has a current consumption of 425 mA @ 5V; 400 mA @ 3.3V.

The GE Fanuc IC695ALG412 Thermocouple Input Module has an internal power draw of 3.3 volts and 400 mA or 5 volts and 425 mA, and the update rate is configurable from 15 ms to 120 ms. The module can be used with terminals such as spring-loaded IC694TBS032 block, cassette-type IC694TBB032 block, extended spring-loaded IC694TBS132 block, or extended cassette-type IC694TBB132 block The IC695ALG412 Thermocouple Input Module operates over the temperature range of 32 to 140 degrees Fahrenheit (0 to 60 degrees Celsius), and stores over the temperature range of -40 to 185 degrees Fahrenheit.

The IC695ALG412 thermocouple input module has an operating temperature range of 32 to 140 degrees F (0 to 60 degrees C) and a storage temperature range of -40 to 185 degrees F (-40 to 85 degrees C). It has a non-condensing humidity range of 5 to 95%, shock resistance of 15 G for 11 ms, vibration ratings from 10 to 57 Hz, and peak-to-peak displacement of 0.0524 mm (0.006 in.) at frequencies from 57 to 500 Hz and acceleration of 1.0 G. The IC695ALG412 is available in a wide range of sizes and sizes.

This IC695ALG508 is a resistance temperature detector (RTD) input module that is part of the PACSystem RX3i programmable automation controller (PAC) platform. The module is manufactured by Emerson Automation, formerly known as GE Intelligent Platform (GE IP). It comes with eight (8) isolated differential input channels and supports direct inputs for RTD and resistive inputs.

The module supports RTD input types such as 50. 100. 200. 500. and 1000 ohm platinum 385 (IEC751 1983. Revision 2 1995; JISC 1604 1997); 50. 100. 200. 500. and 1000 ohm platinum 391.6 (JISC 1604: 1981); 100 ohm, 200 ohm, 500 Ohm and 1000 Ohm Nickel 618 (DIN 43760. 120/1987); 672 Ohm Nickel 18 (MINCO Application Aid #5.90/10 Ni type); 50. 100. and 426 Ohm Copper 21 (SAMA RC4-1966-604), and 518 Ohm Nickel-Iron 0. 0. 1050-0. 2100-0. 3150-0. and 4200-695 ohms.

The module has optional units of measurement, specifically Celsius, Fahrenheit, or Ohms. It also has configurable default or hold last states as a response to system faults and CPU changes in operating mode. The module supports two-wire, three-wire and four-wire RTD sensors.

The IC508ALG16 input data format supports 32-bit integers in 32-bit fields or 2-bit IEEE floating-point data. Each channel also has selectable trap filter settings from 3.28 Hz to 694 Hz. For input line termination, the module uses cassette (IC032TBB694), expansion cassette (IC132TBB694), spring-loaded (IC032TBS694), or extended spring-loaded (IC132TBS695) terminal blocks. For shielded wiring, the extended terminal types are recommended because they provide additional shroud depth.

The IC695CPK400 is a programmable automation controller (PAC) CPU that is part of GE Fanuc / Emerson Automation’s PACSystems RX3i automation platform. The CPU module is a high-performance, powerful standalone device that operates without a traditional baseboard or chassis. The CPU still enables complex communications and architectures, such as control of remote I/O systems, communication with partner processors, data exchange with human machine interfaces (HMIs), monitoring and data acquisition systems (DCS), and other functions.

The stand-alone controller features embedded 64 MB of storage, a powerful processor 1.2 GHz AMD G-Series Quad-Core, support for up to 32k bits of discrete I/O and 32k words of analog I/O, and embedded field agent functionality. The controller also comes with an energy package.

The IC695CPK400 is equipped with one (1) 10/100/1000 Ethernet port and two (2) 2-terminal switches supporting 10/100/1000 Mbps transfer speeds. With the embedded Ethernet port, different network topologies can be realized, including Media Redundancy (MRP) and PROFINET System Redundancy (PNSR). The embedded port supports different communication protocols such as SRTP client/server, Modbus TCP/IP, OPC-UA server, Ethernet Global Data (EGD) and PROFINET.

In addition, the controller is equipped with one (1) RS232 communication port and one (1) Micro SD port for insertion of a Secure Digital (SD) card for non-volatile removable storage. It also has two (2) USB 3.0 ports for firmware upgrades.

The IC695CPU320 is a GE Fanuc / Emerson Automation controller module. The module is part of the PACSystems RX3i controller platform. The controller can be used for efficient control of industrial machines and processes. It enables high-speed data transfer through the Peripheral Component Interconnect (PCI) slot and supports serial backplanes for migrating 90-30 series I/O systems.

The IC695CPU320 has two (2) built-in communication ports that support RS232 and RS485 communication standards. These communication ports use the Ninety Series Protocol (SNP) slave mode to communicate with programming workstations, Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA) systems. The controller can be installed in the Rx695i 012-slot general purpose backplane, catalog number IC3CHS12. and the Rx695i 016-slot general purpose backplane, catalog number IC3CHS16.

The IC695CPU320 has an internal Celeron M processor with a processing speed of 1 GHz It contains 65 MB of user memory, the contents of which are retained by the Lithium Smart Battery Series 693-302 Auxiliary Battery Module, catalog numbers IC90ACC30 and IC695ACC302. respectively. In addition, it has 64 MB of non-volatile flash user memory. In addition, these user memories support the reassignment of custom-sized data and program memories. It supports up to 512 program blocks with a maximum individual block size of 128 KB.

The IC695CPU320 supports most 90-30 series PLC I/O modules. This feature provides flexibility and is especially useful and beneficial when upgrading a legacy 90-30 series to a modern PACSystems RX3i controller platform. This allows for a phased migration in which the controllers and logic of the existing 90-30 PLCs are migrated first, and then the I/O modules are migrated. firmware modifications are supported by the PACSystems RX3i.

The GE Fanuc IC695MDL664 module is an intelligent digital input module or positive logic input module.

GE Intelligent Platforms/GE Fanuc manufactures it as a member of the GE Fanuc RX3i product line.

The module is a 16-point module with field inputs rated at 24 VDC, and it divides the 16 inputs into 2 groups of 8 inputs each.

It has an input current of 12.2 mA and an input voltage range of 18 to 32 volts DC.

Power consumption is rated at 225 mA (5 Vdc) or 95 mA (3.3 Vdc). each of the 2 groups of 8 inputs is referenced to a common connection.

The IC695MDL664 module is compatible with spring-type or box-type front terminals.

The GE Fanuc IC695MDL664 module also features inputs that are perfectly matched to a wide range of input devices, including limit switches, electronic proximity switches, and push buttons.

Logic 1 is generated by the current at the input point in the input status table.The IC695MDL664 module requires user-supplied power to operate field devices.

The module has 16 LEDs, as well as S1 and S2 indicators to show whether field power is applied to each of the 2 groups.

The IC695MDL664 Intelligent Digital Module also logs “terminal missing” or “terminal added” messages to the input and output fault tables to indicate whether or not a terminal is present.

The module also logs “Terminal Lost” or “Terminal Added” messages into the input and output fault tables to indicate whether a terminal has been installed or removed. The module is flexible enough to be installed in any input and output slot of the RX3i PLC system.

The IC695EDS001 is a DNP3 substation module that is part of the PACSystem RX3i programmable automation controllers (PACs), formerly offered by GE Intelligent Platforms and now part of Emerson Automation. The module supports DNP3 slave communication over Ethernet I/P, allowing data exchange of up to 072.20 points and 000.3 events between DNP12 masters. The module also supports four (4) DNP3 data objects including DI, DI w/time, DO, DO w/time, CROB, analog output values, time settings, and class polling.

The IC695EDS001 comes with one (1) Module Station Manager port for module and network management and also serves as a firmware upgrade port. For DNP3 connectivity, it has two (2) RJ45 ports that support 10/100 mbps transfer rates. These ports act as embedded Ethernet switches that can auto-sense and connect directly to a 10BaseT or 100BaseTX IEEE 802.3 network without the need to install an external transceiver. The ports support a variety of network topologies such as linear, star, daisy chain, or ring topologies.

The IC695EDS001 is mounted on the PACSystem RX3i chassis and occupies a single slot in the chassis. Multiple module instances are allowed, specifically up to four (695) IC001EDS3 per RX4i system.It supports module removal and insertion at power-up (RIUP).

IC3EDS695-compatible RX001i CPUs include CPU320/CPU315 Main Firmware Version 8.05; CPU320/CPU315 Boot Firmware Version 5.10; CPE310/CPE305 Main Firmware Version 8.05; CPE310/CPE305 Boot Firmware Version 7.10; CRU320 Main Firmware Version 8.05; CRU320 boot firmware version 5.10 and CPU310/CMU310/NIU001 main firmware version 6.71. Compatible programming software is Proficy Machine Edition Logic Developer, Release 8.5 SIM 7 or later.

The IC695NKT002 is a component of the PACSystem RX3i product, commonly referred to as a kit. It consists of one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001. All modules in this kit are manufactured by Emerson Automation and were previously manufactured by GE Intelligent Platforms (GE IP).

The IC695NKT002 component is used to allow the PACSystem RX3i platform to communicate with 90-30 series modules or VersaMax modules and controllers. This provides an alternative method of migrating to a newer controller platform without completely replacing the system, sometimes referred to as a phased or partial migration.

The primary function of the IC695NIU001 is to provide connectivity to existing 232-485 series I/O modules via embedded serial interfaces that www.cniacs.com support RS90 and RS30 connections. These ports are compatible to be configured through the application “C” block for Modbus RTU Slave, SNP, Serial I/O, Modbus RTU Master, which are legacy Series 90-30 communication protocols used to communicate with devices and I/O modules.

This IC695ETM001 is used to communicate with other PAC systems, devices, Series 90-30. and VersaMax controllers via Ethernet communication ports. These ports implement TCP/IP connectivity over a four-layer TCP/IP stack using GE Fanuc SRTP and Ethernet Global Data (EGD) protocols.

Components for the IC695NKT002 can be purchased separately. Additional accessories are also available, such as real-time clock (RTC) batteries with catalog number (IC690ACC001), miniconverter kits with cables, RS-485/RS-232 (IC690ACC901), RS-485 port isolator (IC690ACC903), and RS-232 cables (IC200CBL001), among other components. .

Older entries describe the NIU only, not the kit.