Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Archives

Home / Articles posted by cniacs (Page 195)
April 7, 2025 BY
IN A-B

A-B 1757-FFLDC4 Fieldbus Link Device

The Allen-Bradley 1757-FFLDC4 is a ControlNet Foundation fieldbus link device.

The module has four (4) Foundation Fieldbus interfaces and one (1) redundant ControlNet interface.

It supports connection to four (4) H1 Foundation Fieldbus networks, each supporting up to sixteen (16) devices.

This link device supports up to 64 fieldbus devices per link device.

The Allen-Bradley 1757-FFLDC4 device is a ControlNet Foundation fieldbus link device.

has four (4) Foundation fieldbus H1 network connections, allowing up to 64 different fieldbus devices to interact in the Foundation network.

It has an additional ControlNet interface for integrating the device into a ControlNet network for monitoring and control purposes.

The ControlNet address of the device should be manually configured using the two rotary switches located on the front left side of the linked device.

The Allen-Bradley 1757-FFLDC4 ControlNet Foundation fieldbus-connected device requires connection to a rated voltage of 24 volts DC (/-10%)

An external power supply rated at 450 mA. It has an inrush current rating of 1.5 amps and a power consumption of 9.6 watts.

A forced ventilation system or climate control system may be required depending on the total heat emitted by all components mounted within the same panel.

Maximum operating temperature should be kept below 60 degrees Celsius (140 degrees Fahrenheit).

The Allen-Bradley 1757-FFLDC4 ControlNet Foundation Fieldbus Connection Device is sized for easy installation on a DIN rail or in any conventional NEMA 4/12 type enclosure.

The most common DIN rails used to mount this connection device are 35 x 7.5 or 35 x 15 DIN rails.

The 1757-FFLDC4 is a panel mount device and is mounted using M4 or #8 screws.

The unit specifically features four (4) Foundation Fieldbus interfaces and one (1) redundant ControlNet interface.

Up to four (4) H1 Foundation Fieldbus networks can be www.cniacs.com bridged via ControlNet media, each supporting up to sixteen (16) devices.

In total, one (1) 1757-FFLDC4 is capable of connecting up to sixty-four (64) fieldbus devices.

This connected device is capable of retaining a programme for up to 21 days when no power is present.

For DC power connections, the 1757-FFLDC4 requires 0.2-1.5 mm2 or 26-16 AWG solid or stranded copper signal wire.

It has an insulation rating of 75°C or 167°F or greater and a maximum insulation thickness of 1.2 mm (3/64 in.).

For fieldbus connections, the recommended wire size is 0.8 mm2 (18 AWG) solid or stranded shielded twisted-pair copper wire with insulation thickness and temperature ratings.

rated for 75°C (167°F) or higher with a maximum insulation thickness of 1.2 mm (3/64 in.). To establish an Ethernet connection, Category 5e cable may be used.
April 7, 2025 BY
IN A-B

A-B 2711-K10G9L1 Standard Operator Terminal

Description

Allen-Bradley PLC 5 high resolution TC/millivolt inputs, natural binary data format, 750 mA backplane current, no external power supply required.

The Allen-Bradley 1771-IXHR is a PLC 5 analogue input module. It is a high-resolution thermocouple/millivolt input module that

used to transfer input data words from its memory to the PLC processor’s data table and to transfer configuration words using block transfer programming.

The 1771-IXHR requires a slot in the 1771 I/O chassis and does not require an external power supply.

The 1771-IXHR module has eight floating differential inputs for thermocouple or millivolt input ranges.

Includes thermocouple types B, E, J, K, T, R, and S and ±100 millivolts. Allows 8 inputs of the same type or allows 4 inputs of different types.

The 1771-IXHR includes cold-end compensation with an accuracy range of 0-60°C and ±0.5°C. It has selectable temperature scales of °C or °F with a temperature resolution of 0.1°C or 0.1°F and a millivolt resolution of 1µV.

It requires a backplane current load of 750mA at 5V and www.cniacs.com has a channel update time of 25ms per 8 channels.

Its wiring is connected to the 1771-WI field wiring arm, eliminating the need to disconnect the wiring when replacing the module.

The 1771-IXHR has a maximum power consumption of 4.255W and a maximum heat dissipation of 14.5 BTU/hour.

The keying strap must be placed between pins 20-22 and pins 24-26 to accept only this module.

The 1771-IXHR module has user-selectable high and low temperature alarms.

It contains a green RUN indicator and a red FLT indicator on the front panel to indicate power and fault status.

When powered on, it performs self-diagnostics and reports status.1771-IXHR provides open-circuit detection in the event of a thermocouple failure.

It automatically calibrates the offset and gain of each channel without potentiometers.
April 7, 2025 BY
IN A-B

A-B 2711-K10G9L1 Standard Operator Terminal

Description

The Allen-Bradley 2711-K10G9L1 terminal is a standard operator terminal produced as part of the Allen-Bradley/Rockwell Automation Panelview 1000 series.

The 2711-K10G9L1 terminal is a standard operator terminal manufactured as part of the Allen-Bradley/Rockwell Automation Panelview 1000 series. It is a DC-powered operator terminal that supports greyscale graphics only.

The 2711-K10G9L1 operator terminal has a 10-inch wide screen. This terminal is a keypad type terminal.

The 2711-K10G9L1 operator terminal’s keypad includes several different keys such as navigation keys, numeric keys, and function keys.

The Allen-Bradley 2711-K10G9L1 terminal is a keypad/touch operator interface terminal that is part of the PanelView family of standard terminals.

Specifically, the 1000 terminal sub-series is used to control and supervise any industrial application activity.

The terminal provides supervisors with all the information they need to check the status of the different devices in the network, send and receive data, and make on-the-fly changes to processes.

The device was developed by Allen-Bradley. the key benefits of the 2711-K10G9L1 Interface Terminal are.

Operators can monitor different processes from a specific location, saving travel time and inventory costs.

It is important that its installation and programming process is carried out by a qualified expert to avoid problems during operation.

It is also important to follow all the steps mentioned in the installation manual.

The keypad of the Allen-Bradley 2711-K10G9L1 Keypad/Touch Operator Interface Terminal is made of stainless steel film.

It includes navigation and function keys, all of which have a press count of 1 million.

Notably, the keypad makes monitoring and inserting new variables and data very easy.

The communication option for the Allen-Bradley www.cniacs.com 2711-K10G9L1 Keypad/Touch Operator Interface Terminal is an RS-232 (DH-485) port with printer.

It has 310 kilobytes of RAM and 1008 kilobytes of nonvolatile memory.

Memory can be expanded using compatible memory cards from the Allen-Bradley accessory catalogue.

It has a 10-inch screen and has a shipping weight of approximately 7.2 lbs.

Technical Description of the 2711-K10G9L1

Keypad-RS-232 (DH-485) communications and RS-232 printer port 10-inch greyscale display.
April 7, 2025 BY
IN A-B

A-B 6180W-15BPXPH VersaView Industrial Workstation

Product Description

The Allen-Bradley 6180W-15BPXPH is a VersaView industrial workstation.

It is a high performance computer with touch and keyboard inputs, Intel Pentium 4 Celeron 2GHz processor,

512 MB of Random Access Memory (RAM), 15-inch screen, and 90½-264V AC auto or 19-32V DC external power supply.

The 6180W-15BPXPH is a VersaView industrial workstation manufactured by Allen-Bradley. The workstation is a complete system that can be used as an operator or engineering workstation.

The 6180W-15BPXPH is equipped with a 15-inch colour active matrix thin-film transistor (TFT) with a display area of 305 x 229 mm (12 x 9 inches).

It has dual input interfaces such as an analogue resistive www.cniacs.com touchscreen and 32 function, numeric and alphabetic keys.

It also has various interfaces such as printer port, audio output, Ethernet communication port, PS2 keyboard, mouse, USB and VGA port. It also has a 3.5-inch floppy drive and an optical drive.

It also has a hard disc drive (HDD) with 80 GB of storage capacity and 512 MB of random access memory (RAM) installed.

The industrial workstation requires an external power supply of 90-264VAC (with automatic switching) or a DC voltage source of 19-32VDC.

The industrial workstation has an operating temperature of 0-50 °C (32-122 °F) and an operating vibration of 0.006 inches p-p (10…57 Hz). .57 Hz).

.57 Hz); 1 g peak (57….500 Hz), and an operating vibration of 0.006 in. .500 Hz), with an operating shock of 15 g (1/2 sine wave, 11 ms).

The 6180W-15BPXPH touch screen supports calibration for more sensitive and accurate operation.

The 6180W-15BPXPH also has a Basic Input/Output System (BIOS) that can be updated, but make sure that the power supply is not interrupted while the BIOS update is being performed.
April 7, 2025 BY
IN A-B

A-B 2711-M3A19L1 Operator Terminal Human Machine Interface

Description.

The 2711-M3A19L1 Operator Terminal is a miniature operator terminal in the Allen-Bradley/Rockwell Automation Panelview 300 Series.

The screen of this miniature terminal is only 3 inches wide. In addition, the 2711-M3A19L1 miniature operator terminal’s screen displays only monochrome graphics.

The 2711-M3A19L1 Miniature Operator Terminal uses a 24 Vdc input power supply.The 2711-M3A19L1 Miniature Operator Terminal has a keypad with four navigation www.cniacs.com arrow keys and four programmable function keys.

About the 2711-M3A19L1

The 2711-M3A19L1 is an Allen-Bradley PanelView 300 operator terminal.

The discontinued 2711-M3A19L1 PanelView 300 is an operator terminal that connects users to their machines.

The HMI has a 3’ monochrome display. It has an 8-pin miniature DIN RS-232 port that supports (DH-485) protocol.

The 2711-M3A19L1 HMI can be controlled by the user by entering information and data using a miniature keypad.The 2711-M3A19L1 is powered by a 24-volt DC power supply and has 240 KB of memory.

The 2711-M3A19L1’s keypad assembly consists of four (4) function keys (F1 through F4). These function keys are fully configurable and can be assigned local and global variables.

To modify values and constants, a numeric keypad consisting of 0-9 and symbols can be used. Finally, the operator can also select the different operating objects using the navigation keys.
April 7, 2025 BY
IN Advantest

Advantest R3267 High Performance Multifunction Spectrum Analyzer

The R3267 series spectrum analyzers are high-performance, versatile analyzers (with basic features) that respond to customer needs for future public land mobile communications systems with high C/N ratios.

The Advantest R3267 spectrum analyzers provide accurate, repeatable measurements of high-quality digital signals in the 2GHz band ± within 1% frequency span accuracy and -154dBc/Hz dynamic range (typical).

In addition, its 10Hz to 10MHz resolution band with filters is capable of performing 70dB (typical, 5MHz offset) ACP measurements over W-CDMA, making it ideal for testing wideband signals.

Finally, the R3267 has a frequency range of 100Hz to 8GHz, allowing even high-frequency systems to be fully measured.

The front panel of the R3267 consists of the Display section, Power Switch/Connector section, Floppy Disk Drive section, Measurement section, Marker section, Save/Recall section, Display Control section, ENTRY section, REMOTE section, Control section, and Option section.

Remove dust from the exterior of the R3267 by wiping or brushing the surface with a soft cloth or small brush. Use a brush to remove dirt from around the panel keys. Hardened dirt can be removed with a cloth that has been soaked in water containing a mild detergent.

Normally, cleaning the display filter from the front is sufficient. However, if the inside of the filter or the LCD surface is dirty, you can detach the screen filter from the R3267 series by removing the two screws on the front and pulling forward on the right part of the filter. Clean www.cniacs.com the filter with a soft close.

■ Wide frequency range:

R3264:9kHz to 3.5GHz

R3267:100Hz to 8GHz

R3273 :100Hz to 26.5GHz

26.5GHz to 60GHz (External mixer option)

Synchronization available up to 325 GHz

■ Resolution bandwidth (RBW):

10 Hz to 10 MHz, 5MHz (analog)

1 Hz to 100 Hz (digital)

■ Wide dynamic range:-145dBc/Hz (2GHz band, typ.)

70dB or better for W-CDMA ACP measurement  (5MHz offset, typ.)

■ 1µs fast zero-span sweep

■ Simplified, Automated measurements for mobile communications

■ Digital modulation analysis options for 1G, 2G, and 3rd

Generation : PHS, PDC, IS-136. GSM, DECT, EDGE, GPRS IS-95. W-CDMA/3GPP, cdma2000. Bluetooth
April 7, 2025 BY
IN Advantest

Advantest R3172 High Frequency Spectrum Analyzer for Microwave and Millimetric Wave Communications

The R3172 and R3182 are low-cost portable spectrum analyzers capable of performing direct input measurements at a maximum frequency 26.5 and 40 GHz respectively.

Adopting newly designed RF circuitry, both the R3172 and R3182 aim for improved basic performance with their 40 GHz direct input capability. Further, the R3172 and R3182 achieve “best-in-class” performance for average display noise levels of -104 dBm (at 26.5 GHz, RBW 1 kHz) and -106 dBm (at 40 GHz, RBW 1kHz) respectively, and SSB phase noise levels of -91 dBc/Hz (at 26.5 GHz, 20 kHz offset) and -85 dBc/Hz (at 40 GHz, 20 kHz offset) respectively.

Operating frequencies for radio communications have increasing tendency to shift to higher frequencies. Accordingly, the R3172 and R3182 have been developed as personal-use spectrum analyzers capable of use in a wide range of applications from development to manufacturing of high frequency modules, devices, etc.

Description:

The R3172 spectrum analyzer employs a synthetic local method that enables users to perform highly stable and accurate spectrum analysis.

The Edelweiss Test R3172 is a spectrum analyzer capable of performing direct input measurements.The R3172 has a frequency range of 9 kHz to 26.5 GHz.

The portable and compact R3172 improves performance when adding newly designed RF circuits.

In addition, the R3172 achieves best-in-class www.cniacs.com performance at an average display noise level of -106 dBm (426.5 GHz, RBW 1 kHz) and SSB phase noise level (26.5 GHz, 20 kHz offset).

The R3172 is designed to withstand a certain amount of noise on the AC power line and should be used in low noise areas. A noise reduction filter helps avoid ambient noise.

The R3172 has an exhaust cooling fan on the rear panel and a front-facing exhaust port on the bottom. Users are advised not to block these areas as the resulting internal temperature rise can affect measurement accuracy.

The R3172 is safe for use at a maximum altitude of 2000 m above sea level, installation category II, contamination level 2.

To remove dirt from the exterior of the spectrum analyzer, wipe or brush the surface with a soft cloth or small brush. Hardened dirt can be removed with a cloth that has been soaked in water containing a mild detergent.

The R3172 was developed as a personal use spectrum analyzer capable of being used in a wide range of applications.
April 7, 2025 BY
IN Advantest

Advantest R3132N One Spectrum Analyzer For Versatile Applications

Basic functions

Basic functions are reinforced so that R3132/3162 can be used in various fields.  For example, the internal automatic calibration function guarantees the total level accuracy of ±1.5dB, level correction factor can be stored in the internal memory, DDS is employed to improve frequency reading accuracy, and frequency span error is lowered to less than 1%.

The R3132/3162 offer wider dynamic range and lower 2nd and 3rd distortion by improving 1dB compression point.

As a result of increasing the sweep repetition cycles by improving the synthesized local oscillator, 20 traces/second (typ.) data rewriting becomes possible, enabling far more real-time waveform measurement.

high speed GPIB increase, the throughput of automatic measurement.

For many applications

For EMI precompliance measurement, 6-dB bandwidth filters for 9kHz, 120kHz and 1MHz as well as QP detector are equipped as standard.  Optional 200Hz narrow RBW filter can be added.

For high-speed time domain measurement function which is indispensable for mobile communications, optional 50µs sweep is effective.

By using the double-screen display function, you can www.cniacs.com specify the rising/falling edge of TDMA waveform and display the magnified image.

The R3132/3162 series spectrum analyzer has ACP and OBW operation function indispensable for evaluating the transmission characteristic of radio system.

With various other functions such as AUTO TUNE, 1Hz resolution frequency counter, dBc/Hz, %AM, and PASS/FAIL test by limit value, the R3132/3162 series can easily perform several types of measurements.

Even for signals which are lower in level than the average noise level, the preamplifier ensures level calibrated, high-accuracy measurement.

For measuring the attenuation characteristic of filters or the frequency characteristic of cables, etc., built-in tracking generator is available as option.  Because the output level can be set in a wide range, it is possible to measure amplifier gain, frequency response, etc.
April 7, 2025 BY
IN Advantest

Advantest R6144 Programmable DC Voltage/Current Generators

The R6144 is precision voltage and current generators ideal for evaluation of precision circuits and parts as well as calibration of temperature controllers.

The units use a time-sharing D/A conversion circuit which provides excellent linearity and stability. Settling time and output noise are greatly reduced for higher reliability, allowing construction of a high throughput measurement system.

GPIB and BCD parallel interfaces are provided as standard features, enabling compatibility with a wide range of host devices such as personal computers, sequencers or general purpose I/O interfaces.

 ■ Up to 32 V/160 mA Voltage, Current Output

 ■ High Resolution (1 µV/100 nA steps)

 ■ High Accuracy Guaranteed For 6 Months: 0.03% (Voltage), 0.035% (Current)

 ■ Low Noise Increases Measurement Reliability: 3 mVp-p, One-Fifth of Previous Models’ Noise Level

 ■ Reduced Settling Time Enables Improvements In www.cniacs.com Throughput: 50 ms, One-Third of Previous Models’ Time

 ■ Built-In 160-Step Memory

 ■ All-Digit Continuous Variable Sweep Function Enables Wider Range of Measurement Applications

 ■ Programs Written For Previous Model (TR6142) Can Be Used Without Modifications
April 7, 2025 BY
IN Advantest

Advantest R6245/6246 DC Voltage/Current Sources/Monitors

■ Synchronized 2-Channel Generation, Measurement

■ Measurement Resolution of 1 µV, 10 fA (SMU220-2), 100 pA (SMU62-20)

■ Source Range ±220 V, ±2 A (SMU220-2, 2.4 W)/±62 V, ±20 A (SMU62-20, 140 W)

■ Minimum Pulse Width 100 µs, Minimum Step 700 µs

R6245/6246 DC Voltage/Current Sources/Monitors

The R6245/6246 Series are DC voltage/current sources and monitors having source measurement units (SMUs) with 2 isolated channels. 

The series covers wide source and measurement ranges.

It is ideal for measurement of DC characteristics of items ranging from separate semiconductors such as bipolar transistors, 

MOSFETs and GaAsFETs, to ICs and power devices. 

Further, due to the increased measuring speed www.cniacs.com and synchronized 2-channel measurement function, 

device I/O characteristics can be measured with precise timing at high speed which previously difficult to accomplish.

Due to features such as the trigger link function and the sequence programming function which automatically performs a series of evaluation tests automatically, the new R6245/6246 enable much more efficient evaluation tests.

 ■ High Measurement Accuracy of ±620000 Columns, 0.02%

High Measurement Resolution of 1 mV, 10 fA 

 ■ High source Accuracy of ±62000 Columns, 0.03%

 Wide source Range of ±220 V, ±20 A

 ■ High Throughput, 0.8 V/µs (At Current Measurement Range of 6 mA or more)

 ■ Wide Variety of Measurement Functions

 • 4 Phenomenon Output (Source/Sink)

 • Up to 5 V Remote Sense

 • Minimum Step 700 µs Sweep Measurement (Generation, Measurement, Data Storage)

 • Range Switching without Discontinuous Output

 • Pulse Measurement with Minimum Pulse Width of 100 µs

 • Synchronized 2-Channel Measurement Function

 • Search measurement function

Menu

Search for products

Back to Top
Product has been added to your cart