Category: A-B

Description:

The Allen Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is designed to provide the integrated and distributed solution needed to monitor and control critical industrial machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines, high-speed compressors, and other reciprocating or rotating machines.

About 1444-DYN04-01RA

The Allen-Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is used to provide the integrated and distributed solution needed to monitor and control critical machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines,

high-speed compressors, and other reciprocating or rotating machines. In addition to this, the 1444-DYN04-01RA module measures strain or pressure,

In addition, the 1444-DYN04-01RA module can also measure dynamic signals such as strain or pressure, vibration, and position measurement signals such as rod position, differential expansion or thrust.

The 1444-DYN04-01RA module allows real-time measurements to protect machinery from imminent failure.

In addition, the measurement results can be further processed to calculate the acute fault indication parameters required to assess the current and predicted health of the machine.

The 1444-DYN04-01RA module can be managed and configured via a Logix controller and connected via an EtherNet/IP industrial network.

As with the rest of the Allen-Bradley/Rockwell Automation Integrated Architecture system, the

As with other parts of the Allen-Bradley/Rockwell Automation Integrated Architecture system, other system components such as visualisation products, controllers, and I/O products can be applied to the 1444-DYN04-01RA module to meet specific needs and applications.

Expansion modules for the 1444-DYN04-01RA module include a relay module, a tachometer signal conditioner and an analogue output module.

About the 1746SC-INO4I

The 1746sc-INO4I is Spectrum Controls’ analogue pure current output module. The module has four (4) isolated channel outputs.The 1746sc-INO4I occupies one slot in the 1746 Input/Output Chassis.The 1746sc-INO4I draws 120 milliamps of current from the backplane at 5 volts DC, but in order to minimise current loading on the backplane, the 1746sc-INO4I can be interfaced with an external power supply rated at 24 volts DC. The 1746sc-INO4I has a DIP switch that specifies whether the module is to be powered from the backplane or from an external power supply. When the DIP switch on the 1746sc-INO4I is set to the rack position, the module is powered from the backplane, and when the module is powered from an external 24 Vdc power supply, the DIP switch should be set to the EXT position.

The 1746sc-INO4I draws 5 volts DC from the backplane. This consumption rating is the same when the module is powered externally. The module has a removable 16-bit terminal block that accommodates Belden 8761 shielded twisted-pair cable. 1746sc-INO4I has 16-bit resolution, 366 nano-amps per count, and 320 microvolts per count. 1746sc-INO4I isolated channel analogue output models have auto-calibrating programmable limits and safety states, and are optically isolated for The 1746sc-INO4I isolated channel analogue output model has auto-calibrated programmable limits and safety states, and is opto-isolated to 750 volts DC (channel-to-channel, field wiring to backplane). 1746sc-INO4I is rated for thermal power dissipation up to 4.5 watts, with a maximum update time of 33.7 milliseconds for all 4 parallel channels, and a step response time of 1 millisecond. In addition, the 1746sc-INO4I is UL/CUL Class I, Division 2. Groups A, B, C, D, and CE listed.

Part number 1746sc-INO4I SLC 500 compatible module is an analogue output module manufactured by spectrum control. This module is manufactured by Spectrum Controls, an Allen-Bradley partner.

Encompass Partners is an Allen-Bradley approved and certified partner to provide Allen-Bradley compatible products.

Allen-Bradley 1771-A4B is a general purpose I/O enclosure.

The Allen-Bradley 1771-A4B is a general purpose I/O chassis.

The hardware is a sixteen (16) slot chassis designed to provide backplane connections and to accommodate 1771 PLC modules.

It provides a maximum backplane current of 24 A and is designed for panel mounting. It has a total weight of 7.3 kg or 16 lbs.

About the 1771-A4B

The Allen-Bradley 1771-A4B is a general purpose I/O chassis that is part of the 1771 Programmable Logic Controller (PLC) product family.

The chassis has sixteen (16) I/O slots that contain electronic circuitry, specifically the backplane, which distributes power to the connected modules.

It is also equipped with hinges for field wiring arms.

The 1771-A4B has an operating temperature range of 32-140 degrees Fahrenheit or 0-60 degrees Celsius.

Hardware storage temperature is -40 to 185 degrees Fahrenheit or -40 to 85 degrees Celsius.

Relative humidity is 5-95% non-condensing. When installing this general purpose I/O chassis, panel vibration and shock should be kept within 2g and 15g at 10-500 Hz, respectively.

The 1771-A4B receives power from the 1771 processor and has an internal power supply that provides 2-4 amps,

The built-in power supply provides 2-4 amp, 3-8 amp rated output power modules, and an external power supply with 6.5-16 amp output current.

In general, do not install external power supplies and power supply modules on the 1771-A4B. Such power connections are incompatible and will result in a substandard hardware configuration.

The 1771-A4B chassis has 16 I/O slots. It measures 12.4 x 24 x 7.6 inches and weighs 14.8 pounds.

When installed in a 1771 PLC-5 system, it utilizes the backplane mounting method with adequate spacing and an open enclosure.

The backplane of the enclosure has a DC voltage of 5 volts and a current of 8 amps.

Allen-Bradley® MP Series

Low-inertia, high-output brushless servomotors incorporate innovative design features that significantly increase torque while reducing motor size.

These compact, highly dynamic brushless servomotors from Rockwell Automation are designed to meet the demanding requirements of high-performance motion systems.

This series of servo motors is commonly used with Allen-Bradley Kinetix® 6000. Kinetix 6200. Kinetix 6500.

Kinetix 300. and Kinetix 350 servo drive families.

These motors are available in nine frame sizes and offer continuous stall torque from 0.26 to 163 Nm (2.3-1440 lb-in) and peak torque from 0.77 to 278 Nm (6.8-2460 lb-in).

MP Series low-inertia motors are available:

– Innovative winding technology that delivers up to 40% more torque per unit size than conventional servomotors

– Improved winding insulation for enhanced thermal management and heat transfer for improved performance

– High-energy rare earth magnets for faster acceleration

– New SpeedTEC DIN connectors allow free positioning of connectors and a single cable family for all MP series motors

– Integrated 24 volt brake option

– Wide torque range – all motors in the same series

– Optional shaft seal with IP 66 environmental rating

– Standard IEC 72-1 mounting dimensions

– Operating Temperature Range 0 – 40º C (32 – 104º F)

– MP Series low inertia motors are UL recognized for components meeting applicable UL and CSA standards and CE certified for compliance with all applicable directives.

Description of the Allen-Bradley 1336-FAN-SP5A

The Allen-Bradley 1336-FAN-SP5A is an assembly for Bulletin 1336 drives.

This unit is a cooling fan that mounts on the side of the heat sink of the 1336 Plus, Plus II, Impact, and Force drives. For use with G and H model hard drives.

About the 1336-FAN-SP5A

The 1336-FAN-SP5A is a replaceable cooling assembly that installs on Allen-Bradley’s 1336 Plus,

Plus II, Impact, and Force adjustable frequency AC drives from Allen-Bradley. The fan is mounted on the heatsink side of the Frame H and G drives.

It is a Class 3 component of the 1336 drive and is labeled FAN in the Troubleshooting Symbols Guide. a C-HB1 cap is included.

Outputs 250 HP, 300 HP, 350 HP, 400 HP, 450 HP, 500 HP, 600/650 HP, or Frame G drives and 700 HP drives.

One (1) of these assemblies is used per drive for 250 HP, 300 HP, 350 HP, 400 HP, 450 HP, 500 HP, 600/650 HP, or Frame G drives and 700 HP, 800 HP, or Frame H drives.

Since the entire 1336 drive has been phased out, this component has also been declared obsolete.

Since Rockwell Automation no longer manufactures this product, this part is only available as a spare part.

Fans are an important part of almost all compact units. The power dissipation of Rack G and Rack H drives ranges from the relative parameters to the fan performance.

can be found under drive parameter 70 (heat sink temperature). The minimum value for this parameter is 0. The maximum value is 255 degrees Celsius, but the drives operate at temperatures from 0 to 50 degrees Celsius.

In addition to the integrated fan, the hard disk’s environment can be properly maintained at the specified operating temperature by following the required mounting clearances and installing an appropriate climate control device.

It is important to note that the fan exhausts air from the hard disk, which means that hot air from the hard disk remains in the case.

An enclosure fan can be installed to pull air from the enclosure to continuously remove hot air from outside the panel.

The Allen-Bradley 1336-FAN-SP5A Heatsink Fan Replacement Kit with Fan Capacitor is for the

Allen-Bradley 1336 Plus, Plus II, Force, Impact, and Force Frame G and

H adjustable AC drives (known as Fan 2). It provides cooling and temperature control for the drive.

The package includes a fan with leads, sealant, a connector with leads, 2 fittings, and a grommet.

About the 1336E-B030-AN-EN-GM1-HA2-L7E

The 30 hp 1336E-B030-AN-EN-GM1-HA2-L7E drive is an Allen-Bradley AC drive that is part of the Allen-Bladley 1336 IMPACT product family.

For the Rack C 1336E-B030-AN-EN-GM1-HA2-L7E drive, the outputs and inputs are connected to TB1. which is the 11-position terminal block on the gate drive board.

National wiring codes should be considered during wiring to minimize the risk of injury and equipment damage.

The drive control interface supports TTL contacts. Encoder feedback is also provided on the drive.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive is available with an output power of 22 kW or 30 hp at 380 to 480 volts AC input voltage.

Output current and apparent power ratings are 48.2 amps and 38 kVA, respectively.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive draws 49 amps and 32 to 41 kVA at the input.

The input and output frequency ranges are 47 to 63 Hz and 0 to 250 Hz, respectively.

The driver output is capable of sustaining 100% of the rated current continuously or 150% of the rated current for up to 1 minute.

The maximum short circuit rating is 200.000 amps RMS symmetrical. The HMI is part of the standard driver package, which includes the controller and programmer.

Digital potentiometers are also available on the driver. The drive has an English language module. For network communications, the drive has a single point remote I/O interface.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive is an open drive with an IP00 enclosure.

The recommended operating ambient temperature range is 32 to 122 degrees Fahrenheit. The drive has a shipping weight of 38.6 kg.

The dimensions of the drive rack are 701 x 301.8 x 225.0 mm.

1336E-B030-AN-EN-GM1-HA2-L7E Technical Description

The Allen-Bradley® Stratix® 5800 managed industrial Ethernet switch delivers Gigabit performance in a flexible package.

Its fixed and modular design supports a variety of copper, fiber, and PoE expansion modules, and offers Layer 2 switching or Layer 3 routing firmware options to meet a variety of application needs.

When used as a Layer 2 switch, the Stratix 5800 is ideal for high-performance end devices.

When used as a Layer 3 switch, routing can be enabled between segmented networks to improve performance and prevent unwanted network traffic.

Network segmentation helps simplify security management by establishing trust domains and improving efficiency.

The Stratix 5800 includes a robust set of switching, routing, and security features to support a wide range of architectures and uses the Cisco IOS-XE operating system to optimize compatibility with enterprise environments.

Choosing a switch co-developed by Rockwell Automation and Cisco allows your operations technology (OT) and information technology (IT) professionals to leverage the tools and techniques they are familiar with.

By helping to provide optimized integration, you can experience easier commissioning and actionable diagnostics.

Features and Benefits

– Full Gigabit switch platform High-performance networking support

– Fixed and modular options with up to 26 ports for flexibility and scalability

– Multiple copper, fiber and PoE options to support a variety of applications

– Supports Layer 2 access switching and Layer 3 routing for use in multi-tier architectures

– Supports IT and OT configuration and management tools, enabling users to leverage the expertise of both teams

– Provides default configurations for industrial applications for easy setup and optimized performance

– IEC 62443-4-2 certified for compliance with global cybersecurity standards

Optimized integration

– Studio 5000® Add-On Profiles (AOPs) enable optimal integration with Rockwell Automation® Integrated Architecture® systems.

Integration into Rockwell Automation® Integrated Architecture® Systems

– Predefined named Logix tags for monitoring and port control

– FactoryTalk® View panel for status monitoring and alarming

– Embedded Cisco® technology, including the IOS-XE operating system, facilitates secure integration with corporate networks

Our Kinetix® 5700 servo drives are designed for machines with large axes and high power requirements.

These high-performance servo drives utilize leading-edge technology designed to help you build machines that are more capable, more flexible, and more energy efficient than ever before.

The Kinetix 5700 servo drives utilize EtherNet/IP communication technology that

Complete your Logix control system with fast access to the data you need, while simplifying your system by using one network to integrate motion and safety functions.

New Features

Tuning-Free Startup and Operation

The Kinetix 5700 server’s V13 firmware has updated features that reduce or eliminate debugging efforts.

Enhancements include.

Virtual Torque Sensor feature detects anomalies and provides analysis

Adaptive tuning now includes multiple tracking trap filters and improved filter configurations.

Command trap filters reduce load oscillation in applications without load sensors

Supports 200V and 400V rated motors

OVERVIEW

High-performance Kinetix 5700 servo drives help meet the demands of demanding applications in a wide range of industries.

These multi-axis servo drives combine high-performance servo and vector motor control to help simplify machine design and reduce the time and labor costs required for integration.

Kinetix 5700 servo drives can be configured with integrated drive safety and regenerative bus power to help make your next servo solution safer and more energy efficient than ever.

Functional Features

Kinetix 5700 Servo Drive

Delivers high power density in a compact rack size

Offers a wide power range of 1.6…. .112 kW wide power range

Supports servo and induction motors with a wide range of feedback types

Features a dual-axis module

Innovative snap-in bus system for easy assembly and installation

Supports single-cable solutions for motor power and feedback

Includes dual Ethernet ports to support linear and device level ring (DLR) topologies

CIP security features support defense-in-depth approach to network security

Kinetix 5700 Integrated Safety Servo Drive

Includes integrated or hard-wired safety options

Integrated safety option reduces overall system wiring

Advanced safety features with Safe Torque Off, Safe Stop and Safe Monitor functions

The 2198-S160-ERS3 has a three-phase power output of 60.1 KW, an internal capacitance of 1120 μF, and requires 92.3 A DC input current at 458-747 V DC.

When the servomotor connected to the inverter does not have a holding option, the inverter has a control current of 4.6A at 24V DC supply.

The inverter also has a control current of 9.6A at 24V DC if the servomotor has braking enabled,.

And the inverter will receive 4A inrush current under 24V DC.

The 2198-S160-ERS3 has an operating heat sink relative to the percentage of rated output power of the inverter of

270W at 20%, 420W at 40%, 570W at 60%, 760W at 80%, and 950W at 100% of utilized output power.

Motor feedback and auxiliary feedback are provided via a 15-pin universal feedback connector (UFB) and a 2-pin motor feedback connector (MF).

and is pre-installed with an EtherNet network connection port.

The 2198-S160-ERS3 has an operating temperature range of 0-50°C (32-122°F), a non-condensing relative humidity of 5-95%, and a storage range of -40-70°C (-40-158°F).

It has a mounting height of 1500 meters (4921 feet), is not rated, and can withstand 15G operational shock and 2G vibration from 55-500Hz.

It is c-UL, CE, KC, c-TICK, ODVA, and OSHA certified and has an IP20 protected enclosure.

The 2198-S160-ERS3 weighs approximately 6.8Kg (15 lbs) and measures approximately 252mm x 478mm x 100mm (9.92″ x 18.82″ x 3.94″).

The 1756-IF4FXOF2F is a ControlLogix discrete high-speed analog I/O module.

It has four (4) high speed, sub-millisecond, differential inputs and is compatible with input signals ranging from ± 10V 0…. .10V 0… .5V 0… .20 mA.

It also has two high-speed voltage or current outputs with an output signal range of ± 10V 0…. .20 mA.

About the 1756-IF4FXOF2F

The Allen-Bradley 1756-IF4FXOF2F is an analog combo I/O module.

The module is part of the ControlLogix system and is compatible with the 1756 ControlLogix chassis, which requires the 1756-TBS6H or 1756-TBCH removable terminal block enclosure (RTB).

The module has four sub-millisecond high-speed differential inputs and two high-speed voltage or current outputs.

The module has a display that shows the module’s health and operating status (e.g., calibration mode).

The 1756-IF4FXOF2F has input ranges of +/-10 volts, 0 to 10 volts, 0 to 5 volts, and 0 to 20 milliamps, and displays over-range when the module is out of these ranges.

Overvoltage protection is 30 volts DC and 8 volts AC/DC. Its open circuit detection is a positive full scale reading within 1 second.

The module has an output range of +/-10 volts, 0 to 20 milliamps, and short-circuit protection, limiting the electronic current to 21 milliamps or less.

It also has 24-volt DC overvoltage protection and open-circuit detection, but is limited to current outputs only (note that outputs must be set to greater than 0.1 mA).

The 1756-IF4FXOF2F has backplane voltage and current ratings of 375 milliamps (at 5.1 volts DC) and 100 milliamps (at 24 volts DC).

The analog inputs and outputs are rated at -10 to 10 volts and 4 to 20 mA, respectively.

Module power consumption is 4.3 watts with 4.3 watts of voltage dissipation and 4.7 watts of current dissipation.

Thermal dissipation is 14.66 BTU/hr for voltage and 16.02 BTU/hr for current.

Current consumption is 375 mA at 5.1 volts and 100 mA at 24 volts.

It has a scan time update cycle of 300us minutes with sub-millisecond channel scanning and multi-module synchronized sampling.

The Allen-Bradley 1756-IF4FXOF2F is a ControlLogix high-speed analog combo module.

The module features four (4) high-speed, sub-millisecond differential inputs that accept ± 10V, 0 to 10V, 0 to 5V, and 0 to 20 mA signal ranges.

Each analog input channel has integrated over- and under-range indication. It is also equipped with two (2) high speed voltage or current output channels with output ranges of ± 10V and 0 to 20 mA.