Category: A-B

The Allen-Bradley 1746-NT8 is an SLC 500 thermocouple/mV analog input module.

The module has eight (8) channels and is compatible with thermocouple sensors such as J, K, T, E, S, R, B, and N. It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV.

It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV. The module is compatible with both stationary and modular SLC 500s.

About the 1746-NT8

The 1746-NT8 is Allen-Bradley’s SLC 500 thermocouple/voltage analog input module.

It is a chassis-mounted, eight (8) channel module that receives thermocouple/voltage signals and converts them to digital signals for retrieval by any SLC 500 processor.

It has a backplane current rating of 120mA at 5V DC and 70mA at 24V DC for a total backplane power of 2.28W.

The 1746-NT8 uses a delta-sigma signal conversion method and has a digital low-pass filter with selectable programmable filter frequencies.

The normal mode rejection between terminals is greater than 100 dB at 50-60 Hz, and the common mode rejection between input and ground is greater than 100 dB at 50-60 Hz.

The 1746-NT8 module automatically calibrates itself approximately every 2 minutes after power-up.

It provides +/-30V DC and 600W pulses for 1ms input overvoltage protection and 12.5V DC circuit isolation between inputs and chassis ground, and between inputs and backplane, with a test voltage of 500V DC for 1 minute.

The 1746-NT8 has nine green LEDs to indicate channel status and module status.

It uses the 1746-RT34 (RTB) removable terminal block to connect the input devices. The terminal block includes two (2) cold junction compensation (CJC) sensors with an accuracy of +/-1.72 degrees Celsius.

The 1783-MX08T switch is an Allen-Bradley managed Ethernet switch.

About the 1783-MX08T

The 1783-MX08T Switch, manufactured by Allen-Bradley, is a Stratix 8000 modular managed Ethernet switch.

The managed switch has up to eight ports and is powered from 24 to 48 V DC.

The 1783-MX08T switch provides an optimized solution for both IT and manufacturing environments.

The Allen-Bradley Stratix 8000 Managed Modular Switch is jointly manufactured by Rockwell Automation and Cisco.

The 1783-MX08T switch features a user-friendly interface that ensures users have an easy installation process and a simple control environment.

In addition, the 1783-MX08T switch supports the RXLogix 5000 operating environment as well as diagnostic panels to further simplify use.

The 1783-MX08T switch is designed to provide simple and secure integration with the corporate network.

 This is accomplished through the CIP interface, which allows integration with enterprise-connected devices.

The Allen-Bradley 1783-MX08T switch measures 112 mm in length, 97 mm in width, and 147 mm in height.

The recommended ambient operating temperature range is -40 to 60 degrees Celsius. 

The ambient storage temperature range is -40 to 85 degrees Celsius and the relative humidity is rated at 5% to 95% non-condensing.

The 1783-MX08T switch has an open housing and supports an inrush current rating of 2 amps.

The unit utilizes a 10/100 Base T Cooper Ethernet port. The supported memory type is CompactFlash memory.

The 1783-MX08F Switch is an Allen-Bradley network switch. The module is an 8-port switch with 100 Base-F fiber optic Ethernet ports.

About the 1783-MX08F

The 1783-MX08F Switch, manufactured by Allen-Bradley, is an 8-port Stratix 8000 switch.

The 1783-MX08F switch has a supply voltage of 24 to 48 volts DC and a power dissipation of 10.1 watts.

The Allen-Bradley Stratix 8000 switch has an open enclosure and uses 100 Base-F fiber optic Ethernet ports.

Modules are of the CompactFlash memory type and are rated at 2 amps inrush current.

The 1783-MX08F switch is 112 mm long, 97 mm wide, and 147 mm high.

To ensure optimal performance, it is recommended that users ensure that the ambient operating temperature range is between -40 degrees Celsius and 60 degrees Celsius.

The 1783-MX08F switch has a relative humidity range of 5% to 95% (non-condensing) and a maximum operating vibration of 2 G at 10 to 500 Hz.

It is rated for 20 G of operating shock and 30 G of non-operating shock.

The Allen-Bradley 1783-MX08F switch supports fiber optic Ethernet data rates of 100 Mbps.

The 1783-MX08F switch is optimized for IT and control/manufacturing control environments.

This makes the 1783-MX08F switch a high-performance managed Ethernet switch.

The 1783-MX08F Switch combines Cisco technology with innovative Allen-Bradley/Rockwell Automaton technology for high performance.

The 1783-MX08F switch is easy to set up and enables comprehensive diagnostic information within the specified Allen-Bradley/Rockwell Automation integrated architecture.

The 1783-MX08F switch provides users with the benefits of a CIP interface with predefined Logix tags and advanced configuration screens.

The Allen-Bradley 1771-IR is a PLC5 resistance temperature detector (RTD) input module.

The module has six (6) input channels and is compatible with copper and platinum RTD types.

It is designed to support temperature measurements in Celsius and Fahrenheit units of measurement. It has a scan time of 50 milliseconds for six channels.

About the 1771-IR

The Allen-Bradley 1771-IR is a PLC-5 RTD input with a natural binary BDC supported data format for actual temperature and ohmic readings.

The unit does not require any type of external power supply. It consists of six three-wire RTD inputs.

The device’s channel update resolution introduces a combination of 50ms/6 channels and 16 bits + sign (1.0 degrees Celsius/1.0 degrees Fahrenheit/bit).

The 1771-IR input module has a voltage range of 100 ohms platinum and 10 ohms other. It has a backplane current range of 800mA.

The DC signal delay is 10ms in the on state, 50ms in the off state, and 45(+/- 15) ms in the AC signal delay in the on state.

These input modules have a lifetime of up to 100 million cycles as they meet voltage requirements of 10-276V AC.

The 1771-IR also helps protect your system by providing appropriate troubleshooting assistance. Module indicators show the status of smart inputs or outputs to help you troubleshoot your equipment.

The 1771-IR has an intelligent hybrid interface for connecting on/off devices such as switches, motor starters, pushbuttons, indicators and signalers.

This unique feature helps save on system engineering and spare parts as well as inventory and training costs.

The front panel of each AC discrete input/output module consists of bright status indicators.

The 1771-IR supports both Celsius and Fahrenheit measurement units. The platinum sensor has a temperature measurement range of -200 to +870 degrees Celsius and the copper sensor has a temperature measurement range of -200 to +260 degrees Celsius.

It has a resistance range of 1.00 to 600.00 ohms and a resolution of 0.1 degrees Celsius or 0.1 degrees Fahrenheit when used with a platinum sensor and 0.3 degrees Celsius or 0.5 degrees Fahrenheit.

Description: Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive component.

The Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive assembly.

It is a 400VAC rated shaft module with a continuous current of 6.1 A and a peak current of 15.3 A. It has a 98% efficiency and a symmetrical 200.000 A (rms) short circuit current rating.

It has 98% efficiency and a symmetrical short circuit current rating of 200.000 A (rms).

About the 2094-BM01-M

The 2904-BM01-M is an Allen-Bradley component designed for use with Kinetix 6000 drives.

The drive is used as an axis module (AM), is in the 400 VAC voltage category, and has a continuous current of 6.1 A and a peak current of 15.3 A. The drive is designed for use with Kinetix 6000 inverters.

The 2904-BM01-M mounts directly to the Kinetix drive power rail. It is typically mounted next to the Integrated Axis Module (IAM) along the power rails, where the module draws power from the power rails to power its internal circuitry.

The axis module connects to the motor and motion device via feedback cables, auxiliary feedback cables, I/O, and safety wiring.

Axis modules also allow the installation of a control module so that control inputs can be integrated into the module.

Модуль сканера A-B 1747-SDN SLC 500 DeviceNet

Description

The Allen-Bradley 1747-SDN is an SLC 500 DeviceNet scanner module.

The module communicates with DeviceNet adapter modules connected to a DeviceNet network.

It is compatible with SLC 5/02 or later controllers. It is a single-slot module that supports operation in slave mode and passes messages in polled, pass-through, state change, cyclic I/O, and pass-through configurations.

It has a backplane current consumption of 5V DC, 500 mA.

About the 1747-SDN

The Allen-Bradley 1747-SDN is a DeviceNet communications scanner.

This scanner module is used to communicate with DeviceNet-enabled devices over a DeviceNet network or through a DeviceNet adapter module.

The module can operate in slave mode; send and receive messages in polled, select-through, state change, and cyclic I/O configurations.

It also supports a pass-through configuration where the 1747-SDN acts as a bridge and connects to a separate DeviceNet network.

This pass-through feature is intended to replace the 1770-KFD, 1784-PCD, 1784-PCID, or 1784-PCIDS DeviceNet connections on the network.

Specifically, the compatible SLC 500 processors when implementing the pass-through configuration are the SLC 5/03. SLC 5/04. and SLC 5/05.

The 1747-SDN supports configuration of up to 63 nodes at a baud rate of 125 Kbps. It draws 5V DC, 500 mA of backplane current.

The 1747-SDN has two (2) LED status indicators mounted on the front panel, such as the Module Indicator to report module operation and a Network Status LED to indicate the DeviceNet communication link.

It also has an LCD display that provides module address and error indications.The DeviceNet terminal is mounted behind the access door and is equipped with a 10-pin plug that plugs into the DeviceNet port.

It serves as an interface between the SLC processor and DeviceNet devices, allowing communication with the processor via M1/M0 file transfer and discrete I/O. The 1747-SDN is compatible with the SLC processor.

The 1769-L30ER is a 5370 L3 CompactLogix controller with 1MB of user memory, dual Ethernet communication ports, and a single USB port.

The integrated communication ports support multi-node and point-to-point interfaces. Ethernet is the primary communication port used by this device to perform data exchange with a variety of devices.

This port supports linear, ring, and star topologies. Up to 16 nodes can be connected to this controller.

These nodes can consist of Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA), databases, converters, gateways, controllers, and other devices.

These embedded ports also act as embedded switches, which means that the same network traffic is experienced on the controller’s dual ports.

There are two (2) ways to assign an IP address to a controller. First, use Allen-Bradley’s BOOTP-DHCP utility.

This utility searches for a unique IP address for the device and assigns it the specified IP address.

The 1769-L30ER controller supports the installation of up to eight (8) 1769 Compact I/O modules.

In addition, up to three (3) expansion groups can be installed to further expand and maximize the functionality of the controller.

The controller is equipped with status indicators such as RUN, FORCE, BAT, OK, I/O. These LEDs are visible to the user and provide feedback on the controller’s operation.

DESCRIPTION

The 825-MCM20 is a currency converter module from Allen-Bradley.

It is part of the 825-P Motor Modular Protection System and is rated for 690 VAC (IEC) and 600 VAC (CSA/UL).

It has an inrush rating of 6 kV, an operating current range of 2.5-20 amps, a continuous thermal current of 24 amps, 

a saturation current rating of 240 amps, and a frequency rating of 50/60 Hz ± 3 Hz.

The converter has a PTC thermistor input and supports six (6) sensors in series.

About the 825-MCM20

The 825-MCM20 is Allen-Bradley’s currency converter module. It is part of the Bulletin 825-P Motor Protection System.

The device is designed primarily to protect industrial three-phase motors, providing thermal overload, 

PTC (positive temperature coefficient) overheat, undercurrent (load loss), current unbalance, and phase loss,

overcurrent (load jamming), short circuit, ground fault (residual), ground fault (zero sequence), 

frequency and other protective functions, as well as motor start/run and other motor start and run protection functions, such as a variety of motor start and run protection.

Protection prohibition at start, start motor timer, notch or pointing device, TCU (thermal capacity utilization) start prohibition, anti-reverse rotation timer, emergency start,

two-speed protection, reduced voltage start (star-delta) and stall switch.

The 825-MCM20 module is specifically designed for use in a variety of line starter applications,

especially low and medium voltage with 2 or 3 potential transformers, with or without phase current transformers,

with or without zero sequence core balancing current transformers, with or without external RTD module, reversing starters, star delta starters and two speed motors.

DESCRIPTION: The Allen-Bradley 825-P is a motor relay used as a protective device for three-phase motors.

It has standard protection features such as thermal overload (thermal model, PTC (positive temperature coefficient), overheat, undercurrent (load loss),

current unbalance and phase loss, overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency. This unit requires 110-240VAC power input.

About the 825-P

The 825-P is a protective relay for use with three-phase motors. Manufactured by Allen-Bradley, the device is

It provides standard protections such as thermal overload (thermal modeling), PTC (positive temperature coefficient), overheat, undercurrent (load loss), current imbalance, and phase loss.

overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency.

For motor start/run protection, this motor relay is capable of starting the motor timer via a protection disable during startup, a startup

notch or pointing device, TCU (Thermal Capacity Utilization) start inhibit, anti-reverse spin timer, emergency start, two-speed protection, reduced voltage start (star-delta), and stall switching to protect the motor.

Descripción

The 2093-AC05-MP1 drive is an Allen-Bradley/Rockwell Automation Kinetix 2000 Series multi-axis servo drive.

It is also an Integrated Axis Module type servo drive. 2093-AC05-MP1 Multi-Axis Servo Drives require clearance on the top and bottom for air-cooling, but not on the left or right sides.

This servo drive can be used with compatible SERCOS fiber optic cables.The 2093-AC05-MP1 Multi-Axis Servo Drive has a three-phase mains input voltage range of 170 to 264 volts AC.

About the 2093-AC05-MP1

The Kinetix 2000 Multi-Axis Servo Drives have output power requirements between 3 – 45 kW (4 – 49 amps) and are designed to provide Kinetix integrated motion solutions for applications.

Kinetix 2000 multi-axis servo drives are available in several series, including the 2093-AC05-MPx, 2093-AM0x, 2093-AMPx, 2093-ASP06.

2093-PRSxx, 2093-PRF, 2094-AL09. 2094-AL15S, 2094-AL25S, 2094-AL50S,

2094-AL75S, and 2094-AL75S-C2. 2093-AC05-MPx is a family of Kinetix 2000 multi-axis servo drives.

It includes the 2093-AC05-MP1. 2093-AC05-MP2. and 2093-AC05-MP5.The 2093-AC05-MP1 consists of one specific assembly.

The 2093-AC05-MP1 consists of a specific assembly that includes the Integrated Axis Module (IAM) mounted on the power rails and is a 230 VAC power converter and inverter.

The power rails (PR) consist of copper bus bars and circuit boards with connectors for each module.

The power rail provides power and control signals from the inverter section to the adjacent inverter, which also consists of compatible servo motors (low inertia, food grade, and stainless steel) and compatible linear actuators.