Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0

Category: Industry Trends

Home / Industry Trends (Page 352)
March 20, 2025 BY
IN GE

IS200ATBAG1B Application Input/Output Terminal Block

The IS200ATBAG1B is an application input/output terminal block manufactured by GE Industrial Systems for use with Innovation Series drive assemblies.

Product Description.

The IS200ATBAG1B is a terminal block assembly manufactured for the GE Innovation Series.

Part of GE’s recent Innovation Series, this IS200ATBAG1B product includes a Windows 2000/XP based operator interface,

Ethernet and DCS communications and Cimplicity software. In particular, the IS200ATBAG1B has been modified by the inclusion of a single functional revision with a ‘B’ rating.

This board provides adequate backplane terminal block connections for all signals from the IS200CABP control plane assembly backplane board

Hardware Tips and Specifications

The overall functionality of the IS200ATBAG1B Application I/O Terminal Board consists of a variety of hardware specifications. The board provides a 60-bit terminal block for all J6 and J7 jumpers connected to the CABP board.

Before purchasing the IS200ATBAG1B www.cniacs.com it should be noted that there is no customisable hardware or manually removable jumpers for this product.

While this is still true, two different versions of this IS200ATBAG1B model exist; due to different pin assignments for connector J6

as well as a different connector J7 and a different pin assignment for the corresponding connector. The J7 connector for this IS200ATBAG1B model is rated at 50V and has a maximum value of 1A.

All J6 connectors associated with this IS200ATBAG1B board are rated at 225 V and 1 a maximum current, except for the following identifiable connectors:

CONA_NO J6 connector

CONA_NC J6 connector

CONA_C J6 connector

RLY1COM connector

RLY1NC connector

RLY1NO connector

RLY2COM connector

RLY2NC Connector

RLY2NO Connector

RLY3COM Connector

RLY3NC Connector

and RLY3NO connectors

In addition to the various connectors compatible with the I/O terminal boards for this application, a specialised breakdown of the individual part numbers for this product

can reveal a lot of pertinent information about the IS200ATBAG1B hardware. Firstly, the IS200ATBAG1B begins with the ‘IS200’ series label.

This label designates the product as a General Electric product manufactured at the Salem, Virginia plant.

This ‘IS200’ designation is followed by the familiar ‘ATBA’ functional acronym, which leads to the IS200ATBAG1B group number and PCB coating type.

The ‘G1’ version of this IS200ATBAG1B product designates it as a Group 1 series product with a common PCB coating.

The total delamination coverage of the normal PCB coating is not as comprehensive as popular alternative conformal PCB coatings, but results in a thicker overall substrate protection layer.

The final noteworthy detail gleaned from the IS200ATBAG1B part number is its single-function version.

The ‘B’ digit in the IS200ATBAG1B, located at the end of the part number, indicates a single-function revision of this terminal block with a ‘B’ rating.
March 20, 2025 BY
IN A-B

A-B 1336 PLUS II Adjustable Frequency AC Drive

With drive power ratings ranging from 0.37 kW to 448 kW (0.5 hp to 600 hp), the

Providing a single solution for virtually all your speed control requirements. The common design of the entire product line, coupled with the same control interface features, equipment

The common design of the entire product line, coupled with the same control interface features, equipment communications, training and maintenance, provides significant advantages for your control needs.

Plus, the same control interface capabilities as Allen-Bradley SMC™ and SMP™ power products, 1305 drives, 1336 IMPACT™ and 1336 FORCE™ field oriented products.

1336 IMPACT™ and 1336 FORCE™ field-oriented control drives, which all use the same control interfaces and communication options.

You’ll gain significant advantages in system www.cniacs.com design, component integration, operator training, and maintenance.

Features

Protection Features

– Detection and tripping:

Undervoltage

Overvoltage

Drive overcurrent

Over temperature

External Signal

Drive Output Short Circuit

Ground fault

Loss of encoder

Temperature

Load loss

Single phase

– Overvoltage stall

– Overvoltage stall speed

– Six drive alarms

– Fault reset input

Function Description

Traverse Function

The 1336 PLUS II output frequency can be programmed to modulate around a set frequency. This can be achieved by setting three parameters to create an inertia compensated delta waveform

– Traverse Period, Maximum Traverse, and P Jump. In surface drive winding applications, the developed waveforms can be used in a traverse drive to electronically perform the traverse function.

The traverse actuator will move the yarn back and forth in a diamond pattern so that the yarn is evenly distributed over the surface of the tube. This pattern must be changed in order to prevent yarn build-up at the same points on the surface. This can be achieved by constantly

continuously changing the traverse speed in a cyclic manner over a specified speed range. Using inertia compensation, a series of distributed diamond patterns can be formed over the entire surface of the tube.

Start-up operation

For applications requiring unattended operation, the 1336 PLUS II can resume operation when power is restored after a power failure.

If the Power On Run feature is activated and the input power supply is disconnected, then when the power is restored

The drive will automatically restart and run at the current commanded speed if all the necessary signals (Enable, Auxiliary, No Stop and Start) are present.

4-20mA Current Loss Option

Many control systems will issue a 4-20mA control signal for the drive to use as a speed reference.

The drive will run at the lowest speed with the 4mA signal and at the highest speed with the 20mA signal.

The drive can also invert this signal to run the minimum speed at 20mA and the maximum speed at 4mA.

Since a minimum signal of 4mA is required, the drive must have a ‘fallback’ command in the event of signal loss (sensor failure or disconnection).
March 20, 2025 BY
IN A-B

A-B Line Synchronisation Module Bulletin 1402 LSM

Products

The Bulletin 1402 Line Synchronisation Module (LSM) is designed to meet the needs of manufacturers of three-phase AC generators and power generation systems,

system integrators and users, or for applications where two three-phase systems need to be synchronised with each other.

The module provides the means for automatic synchronisation, load sharing and high-speed power system monitoring.

The Line Synchronisation Module (LSM) is a two-slot 1771 form factor module that fits into a standard Allen-Bradley 1771 I/O chassis.

It has three functions:

1. measures appropriate parameters from two three-phase systems and provides control and error signals for synchronised control of the engine governor.

2. provide an analogue output representing the ratio of the power supplied by the alternator to the alternator output rating;

To read an analogue input representing the ratio of the total system load to the total system capacity;

and provide an error signal to adjust the alternator for proper load sharing based on instantaneous load requirements.

3. act as a multi-function digital power monitor for the system.

These functions provide data and control signals that are transmitted to the PLC-5 through the 1771 backplane.

Synchronisation and Load Sharing Errors

In order to synchronise two three-phase systems without high transient energy transfer, the voltages, frequencies and phase differences of the two systems must match.

Kilowatt load sharing can be achieved by matching the ratio of the power system load to the system capacity to the ratio of the actual alternator power to the alternator power rating.

The LSM provides the following information so that the customer’s system can achieve the necessary control operations.

– Voltage matching error (in units of 0.05%)

– Frequency matching error or slip (in 0.01 Hz)

– Synchronising bus and reference bus phase matching error (in 1 degree)

– Load sharing error (scalar between 0.000 and 1.000)

– Synchronisation status

– Frequency within limits

– Voltage within limits

– Phase within limits

– Synchronisation mode conflict fault

– Phase rotation mismatch fault (3-phase synchronisation mode only)

– No reference bus voltage fault

– No synchronised bus voltage present fault

– Reference bus overvoltage fault

– Synchronous bus overvoltage fault
March 20, 2025 BY
IN A-B

A-B 1407-CGCM Combined generator control module

Installation requirements

This device is intended for overvoltage applications of category II in industrial environments of pollution class 2 (as defined in IEC publication 60664-1).

The device must be mounted vertically as it contains a heat sink. Any other mounting angle will reduce the heat dissipation capability of the device and may result in premature failure of critical components.

The device can be mounted anywhere www.cniacs.com as long as the ambient temperature does not exceed the rated ambient conditions or clearance requirements.

Clearance requirements for CGCM equipment are

– 63.5 mm (2.5 inches) of clearance is required on both sides of the unit when mounted.

– 101.6 mm (4 in.) clearance is required above and below the unit when mounted.

Electrical Connections

The connection of the CGCM device depends on the application and the excitation programme. It is not possible to use all inputs or outputs in a given installation. Incorrect wiring may result in damage to the equipment.

Connect the terminals of the CGCM unit with copper wire rated at no less than 600V. General purpose wire rated for a minimum temperature of 105 °C (221 °F) may be used.

All wire must be copper. Select circuit wires according to good design practice.

The wire gauge ranges listed in the terminal block label instruction table indicate the physical capabilities of the connector.

Terminals for CGCM devices are located on the front, bottom, and right side panels of the device.

The nine-pin connector on the bottom of the unit is used for communication between CGCM devices in a redundant system. The recommended torque for the terminal screws is 1 N-m (9 lb-in).

Terminals that are used as shield wire landings are found on multiple terminal strips. Shielded terminals with the same name are connected together internally, but are not connected to a protective ground or any internal device circuit.

Excitation power supply

The excitation power supply is connected to the PMG terminals whether it is connected to the generator output (parallel excitation) or to the PMG.

The shunt excitation input is connected to the voltage transformer (VT).

The PMG inputs are located on TB1 and are labelled PMG A, PMG B and PMG C, indicating the respective phase relationship.

The single-phase excitation power supply must be connected to terminals PMG A and PMG C. The PMG inputs require twisted pair connections.

A twisted pair shielded cable is required for the PMG input.
March 20, 2025 BY
IN Foxboro

FOXBORO 43AP Pneumatic Indicator Controller

WIDE SELECTION OF MEASURING ELEMENTS

Invensys Foxboro offers the widest variety of element constructions and ranges in the industry. This versatility enables the 43AP Series Pneumatic Indicating Controllers to be applied to virtually any process.

WIDE CHOICE OF CONTROL MODES

On-off, proportional, proportional plus derivative, proportional plus integral (reset), proportional plus integral plus derivative, differential gap, and www.cniacs.com automatic shutdown actions are available.

BROAD RANGE OF INTEGRAL (RESET) AND DERIVATIVE ADJUSTMENTS

The integral unit has the complete range from 0.01to 50 minutes, and the derivative unit from 0.05 to 50 minutes.

VARIETY OF OPTIONS

These controllers are available with an extensive list of optional features. Among these are internal bumpless automatic-manual transfer stations (two types), “batch” function, remote pneumatic set point, Type 70 electric contacts, and control valve mounting.

ACCURACY UNAFFECTED BY MOUNTING STRESSES

Both the control unit and the measurement element are mounted on a rigid steel plate. Thus, these components are isolated from case stresses due to mounting, and dependable accuracy is ensured.

POWER FAILURES DO NOT INFLUENCE PROCESS-DRIVEN INDICATION

A power failure and the likely subsequent loss of supply pressure do not influence the process-driven indication.

WEATHERPROOF CONSTRUCTION

A glass fiber reinforced case and a gasketed door with a shatterproof polycarbonate window meet IEC IP53 and provide the environmental protection of NEMA® Type 3.

VERSATILE MOUNTING

Instruments may be mounted in a panel, on a flat surface, on a INTERNAL BUMPLESS AUTOMATIC-MANUAL TRANSFER STATION

This option provides bumpless-balanceable transfer between automatic and manual control by simple 2step procedure. Accidental transfer is avoided because the door must be opened to gain access to the transfer station.
March 20, 2025 BY
IN GE

Discrete Output Module for GE Fanuc IC200MDL740 VersaMax Series

Product Description.

The IC200MDL740 is an output module from the VersaMax series manufactured by General Electric Intelligent Platform Control System Solutions.

The module has a total set of 16 output points, each supporting discrete digital signals.

The output points of this device can be either positive logic or source types. Each output point performs load switching and supplies power to the load.

This product is compatible with the IC200CHS series of plug-in relay bases.

This device requires an auxiliary power supply to support output load switching. The five-volt output power supply must not draw more than 45 mA.

This module operates from 10.2 to 30 volts direct current (DC). Although the unit is nominal at 24 volts DC, it can also operate at 12 volts DC;.

However, operation at 12 volts DC requires an upgrade to the IC200MDL740B or higher.

Each output has a current of 0.5 amps and a response time of 0.2 milliseconds for the ‘on’ state and 1.0 milliseconds for the ‘off’ state.

Interchannel isolation is not supported, nor are any protection mechanisms such as internal fuses.

Output voltage drop peaks at 0.3 volts and output leakage is up to 0.5 mA when operating at 30 volts DC. LEDs indicate device status.

These LEDs require field power to operate but are not affected by output load conditions.

This Model IC200MDL740 also supports thermal derating when operating at 24 or 30 volts DC.

The IC200MDL740 discrete output module is a 12/24 volt DC Versamax positive logic output module manufactured by GE Fanuc.

It has 16 discrete outputs, 10.2 to 30 www.cniacs.com volts DC, 12/24 volts DC nominal external supply voltage, and 45 milliamps of backplane current consumption.

The IC200MDL740 Discrete Output Module is a GE Fanuc 12/24 Volt DC Versamax positive logic output module with 1 set of 16 source type outputs.

It has rack-mounting options and a compact design with a hot-plug facility that helps users to easily replace it without changing the field wiring.

The IC200MDL740 Discrete Output Module has LEDs to indicate the status of each output point.

Three types of carriers are available for easy installation or replacement of output modules in the system without interrupting operation.

It has configurable filtering times, a maximum turn-on response time of 0.2 ms, and a maximum turn-off response time of 1.0 ms.

It also provides external power to the load side and operates with backplane power.
March 20, 2025 BY
IN Kollmorgen

Kollmorgen S200 High Performance Compact Brushless Servo Drives

Kollmorgen S200 Servo Drives are the first fully digital industrial drives with a velocity loop bandwidth of 800 Hz.

These compact drives feature high-resolution feedback and high-performance current loop bandwidth for smooth motion and fast response.

This simplifies tuning and increases unrivalled system throughput.

Intelligent feedback with an www.cniacs.com electronic motor nameplate enables plug-and-play commissioning in most applications.

Features

Available for 120/240 VAC and 20-90 VDC operation with current ratings ranging from 1.5 amps RMS continuous to 48 amps RMS peak current

24-bit high resolution feedback

3-5 kHz high performance current loop bandwidth

Intelligent feedback with electronic motor nameplate eliminates the need for drive parameterisation and servo loop tuning, enabling plug-and-play commissioning in most applications

Standard features include torque and speed control bases, electronic gearing, analogue reference inputs up to 18 bits and encoder equivalent outputs

Options available to support indexing or SynqNet™-based programmable motion control

Meets UL 508C, CE, EN50178. EN61800-C and Semi F47 standards

Separate ‘Keep Alive’ power input allows quick recovery from emergency stops

The Benefits

Wide power range allows deployment of a single drive family in a complete machine

Small footprint allows for smaller cabinets or installation close to the point of use

Optically isolated inputs/outputs, positive locking connectors and full failsafe protection to extend machine life and prevent accidental damage

High-performance system designed for increased machine throughput

Easy-to-use graphical user interface reduces engineering and support time

Reduced overall costs

Technical Data

Dimensions

S200 Series Drives

Industry-leading performance in a small package The Danaher S200 Series of brushless servo drives combines high-performance servo technology into a full power range family with DC and AC inputs.

Danaher S200 Series brushless servo drives incorporate high-performance servo technology into a full power range family with DC and AC inputs. Especially for low-power applications, the

S200 Series offers more performance and ruggedness than ever before, without sacrificing reliability or package size.
March 20, 2025 BY
IN Emerson

Emerson 00813-0100-0112 VersaMax Modular Input/Outputs and Controls

The guiding principle of Emerson’s VersaMax is maximum versatility.

This compact, affordable control solution can be used as a compact PLC, distributed I/O, or distributed control.

With its modular and scalable architecture, intuitive functionality and ease of use, this innovative family of controls saves machine builders and end users a great deal of time and money.

Powerful PLCs in a small package

The VersaMax modular CPUs offer many www.cniacs.com features typically found only in larger PLCs, including up to 128kB of application memory.

These include up to 128kB of application memory, floating point, real-time clock, subroutines, PID control, flash memory, and unbuffered programme storage.

Serial port supports serial read/write and Modbus master/slave communications.

Rich and Useful I/O Options

Emerson offers a wide range of discrete, analogue, hybrid, and dedicated I/O modules. These modules can be freely combined

These modules can be freely combined to create stand-alone I/O stations with up to 256 I/O points and extended I/O systems with up to 2048 I/O points.

The perfect match for today’s open systems

VersaMax gives you the freedom to connect via PROFINET (remote I/O only), Modbus/TCP, other Ethernet networks as well as Genius, DeviceNet,

Profibus-DP, etc. VersaMax gives you the freedom to connect to a wide range of host controllers, including PLCs, DCSs, and PC-based control systems.

VersaMax also fully supports the power and open architecture of Emerson’s PC-based control solutions.

Cost-Effective Control and I/O

VersaMax features intuitive diagnostics, module hot-swapping, and quick-connect wiring to extend uptime and

Reduce engineering and training requirements and significantly lower project lifecycle costs.

Designed to Maximise Ease of Use

Every aspect of VersaMax has been carefully refined to meet the needs of the user. Snap-on I/O carriers mean no tools are required for module installation or removal.

Convenient rotary switches can be used to set bus addresses, reducing programming time. With VersaMax, you can even address I/O automatically.

Easy troubleshooting and machine setup

You can easily configure VersaMax I/O using the integrated PAC Machine Edition (PME) software.

PME is the same software as all PACSystems CPUs, so you only need one tool for everything from small to large applications.

This approach utilises the same hardware configuration, network configuration and programming editor. In addition, the QuickPanel+ HMI’s single tag database simplifies HMI development.
March 19, 2025 BY
IN Emerson

Emerson 00813-0100-0161 Compact Programmable Automation Controller

PACSystems™ RSTi-EP CPE200 Series

Compact Programmable Automation Controllers

Everything you need today to meet the business challenges of tomorrow.

The RSTi-EP CPE200 Compact Controller Series, with its built-in safety design, open programming and open communications, simplifies connectivity to traditional sensors and actuators as well as external analytical software platforms.

Simplifies connectivity to legacy sensors and actuators, www.cniacs.com as well as external analytical software platforms, while reducing cost and complexity for OEMs and end users.

The compact controller family simplifies connectivity to traditional sensors and actuators, as well as external analytical software platforms, while reducing cost and complexity for OEMs and end users.

Featuring the same high-performance runtime and toolchain as the PACSystems™ RX3i large-format controller, this compact controller family

It provides large programmable logic controller (PLC) functionality in a smaller footprint.

The PACSystems™ RX3i is designed to provide the functionality of a large programmable logic controller (PLC) in a small footprint, yet be small, cost-effective, and IIoT-ready so machine builders don’t have to sacrifice productivity or performance.

Out-of-the-box cybersecurity

Industrial controls have always been a target for cyber threats. We understand the risks involved in protecting our customers’ most important assets.

We believe in defence-in-depth architecture to secure assets from potential cyber threats.

The RSTi-EP CPE200 Compact Controller Series is Achilles Level 2 certified and has been designed with technologies such as Trusted Platform Modules and Secure Boot to ensure security.

Technologies such as platform modules and secure boot to prevent malicious applications and ‘unauthorised’ operating systems.

Centralised configuration allows encrypted firmware updates to be performed from a secure central location. an extensive set of network security technologies and tools help prevent unauthorised updates.

while built-in secure communication protocols help prevent man-in-the-middle and denial-of-service attacks.

Open communication for supply chain agility

In today’s interconnected global economy, unexpected external events can cause disruption and have a dramatic impact on narrow and rigid sourcing plans.

Now more than ever, organisations need to design systems with supply chain agility in mind.

In order to create flexible supply strategies, leading organisations are looking for products that can anticipate uncertainty.

providing them with maximum freedom to operate effectively no matter what happens.

The RSTi-EP CPE200 compact controller series is designed to enable supply chain flexibility.

We’ve built in open communication features that allow you to easily connect a wide range of third-party devices.

The RSTi-EP CPE200 features real-time I/O networking, up to three 1-Gbps Ethernet ports, and support for all popular communication protocols.

including PROFINET©, OPC UA, Modbus/TCP and DNP3.

The compact controller provides you with the toughness to succeed.
March 19, 2025 BY
IN Emerson

Emerson 00813-0100-0115 RXi – Industrial Monitor

Modularity and flexibility

The RXi – Industrial Monitor Display Portfolio is available in screen sizes ranging from 7 inches to 24 inches, all in widescreen format.

The 7-inch and 15-inch models also feature outdoor sunlight readable (SLR) screens.

The modular nature of the unit provides great flexibility in configuring RXi – Industrial Monitors.

You can easily replace an indoor screen with an outdoor screen, change the screen size, or replace a damaged screen, all while using the same backplane module.

Recognising that effective processes require proper visualisation, the RXi – Industrial Monitor portfolio offers more functionality than ever before.

With display port inputs and display port outputs on every industrial monitor, you can simplify your architecture with MST daisy chaining.

Designed for Visualisation

RXi – Industrial monitors are designed with precision in mind when it comes to visualisation.

Multi-touch, projected capacitive screens feature high resolution, vivid graphics capabilities and fast response times to ensure relevant information is always available for viewing and interaction.

This enables operators to make faster, more informed decisions with a high-performance platform that reduces total cost of ownership.

Anywhere, anytime: a wide range of applications

The portfolio operates efficiently in temperatures as high www.cniacs.com as 65°C and as low as -20°C. The modules can be used outdoors and are available in a variety of configurations. Modules can be used outdoors and are equipped with sunlight-readable (SLR)

Readable (SLR) UV-protected screens.The screens of the RXi – Industrial Monitors are strictly IP66 certified and are protected against dust, humidity and even direct water spray.

RXi – Industrial monitors offer you solutions to meet your every need.

Display technology: designed to maximise the user experience

RXi – Industrial Displays bring industrial displays into today’s connected world, combining design, durability and power.

In an ultra-thin package, it’s perfect for the factory floor.

The sleek and powerful user experience (UX) connects people to machines with the latest touchscreen technology and widescreen displays.

The capacitive ultra-touch screen can be used while wearing personal protective equipment and is as sensitive as the latest smartphones.

In addition, the outdoor-grade sunlight readable (SLR) screen is almost twice as bright as the brightest smart devices.

Optically bonded screens with UV protection greatly reduce reflections and glare, providing operators with vivid, clear images for more complete and powerful process visualisation.

Menu

Search for products

Back to Top
Product has been added to your cart