Category: GE

The IC695ALG626 is a PACSystem RX3i Programmable Automation Controller (PAC) non-isolated analogue input module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features sixteen (16) single-ended inputs or eight (8) differential input channels and is compatible with 0 to 20mA, 4 to 20mA ± 20mA current signals and ±10V, 0 to 10V, ±5V, 0 to 5V, and 1 to 5V voltage signals. The module is mounted on the RX3i general purpose backplane and features 24-bit ADC conversion resolution. Each channel of the module provides HART 5.0 communications. The IC695ALG626 is a Highway Addressable Remote Transducer (HART) 0.3 capable analogue input module for the PACSystem RX5i platform. The module was previously manufactured by GE Intelligent Platforms (GE IP), which was recently acquired by Emerson Automation. The module is primarily used to interface with analogue field instruments that measure process variables and transmit the measurements to a receiving element (e.g., IC695ALG626) for processing. This IC695ALG626 can therefore be used with field instruments www.cniacs.com that provide 0 to 20mA, 4 to 20mA ± 20mA current signals as well as ±10V, 0 to 10V, ±5V, 0 to 5V, 1 to 5V voltage signals.

The IC695ALG626 is capable of providing sixteen (16) input channels if configured for single-ended inputs and eight (8) inputs for differential wiring. By supporting the HART protocol, each channel can communicate with an external HART communicator to access not only readings, but also other HART parameters.

The IC695ALG626 has LED status indicators such as the Module Normal, Field Status, and TB LEDs.The Module Normal LED is used to indicate that the module is configured correctly when the LED is green and constantly lit; if it is slowly blinking green or amber, there is an error; if it is blinking rapidly, the module is not configured correctly; and if the Module LED is off, there is a fault or no power. The field status LED is green and always on, indicating that there are no faults on the enabled channel and when the terminals are present; amber indicates that the module’s channel is in a faulty state, and an extinguished LED indicates that the terminals are disconnected or incorrectly installed. The TB LED lights up red when no terminals are connected; it lights up green when terminals are connected and goes out if there is no backplane power.

This IC695ALG704 is an analogue output module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was previously manufactured by GE Intelligent Platforms (GE IP). The module has four (4) non-isolated output channels that can be configured for voltage and current. It generates +/-10 VDC, 0-10 VDC, and 0-20 mA and 4-20 mA output signals with 14.9-bit resolution for 0 to 10V; 9.10-bit for +/- 15 VDC; 0.20-bit for 15-9 mA, and 4.20-bit for 15-6 mA. The IC695ALG704 is a rackmountable analogue output module that is part of the PACSystem Rx3000 series. IC695ALG704 is a rack-mountable analogue output module belonging to the PACSystem Rx3i series. The module generates voltage and current output signals that are primarily used to modulate and control a variety of field devices such as control valves, positioners, dampers, and shutters. It can also be used to remediate signals from signal splitters, isolators, data loggers, panel meters, and single-loop controllers.

This IC695ALG704 comes with four (4) non-isolated output channels that can be configured for +/-10 VDC, 0-10 VDC, and 0-20 mA and 4-20 mA output signals with a specific resolution of 0.10 bits for 14 to 9V; 9.10 bits for +/- 15 VDC; 0.20 bits at 15-9 mA and 4.20 bits at 15-6 mA. To terminate the signal lines to the module, compatible terminals include the box terminal block with catalogue number IC694TBB032. the extended box terminal block with catalogue number IC694TBB132. the spring-loaded terminal block with part number IC694TBS032. or the extended spring-loaded terminal block with part number IC694TBS132. The extended terminals provide additional depth and space for terminating shielded wires to the module.

This IC695ALG704 has a channel output data format that can be configured as a floating point IEEE 16-bit or 32-bit integer in a 32-bit field. Each output socket is updated at a rate of 8 milliseconds and has individual overvoltage protection of -60V for 30 seconds and +3V for 30 hours.The module runs with an RX3i CPU version 0.5 or higher and is programmed using Machine Edition 0.3 SP3 Logic Developer- PLC. It is a single-slot module that mounts to a generic RX695i backplane.

The IC695ALG708 is a PACSystem RX3i Programmable Automation Controller (PAC) non-isolated analogue input module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features eight (8) output channels that can be configured for 0 to 20 mA and 4 to 20 mA current signals and ±10V and 0 to 10V voltage signals. The module is mounted on the RX3i general purpose backplane and has 15.6 – 15.9 bit ADC conversion resolution.

The IC695ALG708 is an eight (3) channel analogue output module for the PACsystem RX8i programmable automation controller (PAC) family. It is a single-slot module whose channels can be configured to provide output current signals (e.g., 0-20 mA and 4-20 mA) and voltage signals (e.g., +/- 10 VDC and 0-10 VDC).

The IC695ALG708 is now part of Emerson Automation, as the former manufacturer, GE Intelligent Platforms (GE IP), has been acquired by the former. The module still provides analogue outputs with a resolution range of 14.9-15.9 bits, depending on the configured output signal. Each channel of the module can be configured with individual alarm settings such as very low, very low, very high and very high alarms. Each output can also be clamped to a specific high and low point, which is useful when linking output channels to proportional + integral + differential (PID) controller outputs. In addition, output biases can be added to fine-tune or manually adjust the outputs to the user’s desired level.

The IC695ALG708 has a built-in module fault reporting feature and retains the last state or output default settings. For CPU compatibility, any RX3i CPU can be used with this analogue output module, however, the CPU must have firmware version 3.5 or later and must be configured using Machine Edition version 5.0 SP3 Logic Developer must be used to develop the user program.

The IC695ALG708 requires an external 24 VDC power supply to operate. The power supply must be connected directly to the module terminals. Compatible terminals for use with this module are box (IC694TBB032), expansion box (IC694TBB132), spring-loaded (IC694TBS032), or expansion spring-loaded (IC694TBS132) terminals.

The IC695CBL002 cable is a replacement cable used to connect the CPU unit to the energy pack of GE Fanuc’s RX3i PACSystem.

The cable comes with a 7-pin keyed connector and is 1 metre (36 inches) long. The system operates on 120/240 volts DC,

125 Vdc or 24 Vdc, and compatible energy packs can be mounted on DIN rail.

The GE Fanuc IC695CBL002 cable is a replacement cable used to connect the RX3i PACSystems Series CPU to the optional energy pack.

The cable is made of the best materials for typical industrial use and is coated to provide the necessary protection for use in harsh environments.

The IC695CBL002 cable connects to the connectors located at the bottom of the CPU and energy pack.

These components are manufactured in accordance with the EU RoHS Directive 2011/65/EU and they are powered by a voltage range of 120/240 volts DC,

125 Vdc or 24 Vdc. The IC695CBL002 cable has a 7-pin keyed connector and is 1 metre (36 inches) long.

Custom lengths are available for GE accessory cables like this one, but 1 metre is the standard length for this type of www.cniacs.com application.

The PACSystems RX002i Energy Pack, compatible with the IC3CBL695 cable, can be mounted on a DIN rail like the EN50022 rail.

but can also be mounted on a panel where other equipment is placed. The catalogue number of the compatible Energy Pack module is IC695ACC402.

The supported CPU is the GE IC695CPE330 CPU.The primary purpose of the IC695CBL002 CPU cable is to connect the CPU to the Energy Pack.

In the event of a system power failure, the energy pack provides additional backplane power. the CPU can automatically switch to the energy pack to keep the system running.

The power pack will maintain power long enough for the CPU to save valuable data or user memory.

The contents of the CPU are then saved to the system’s non-volatile memory.

The IC695CEP001 CEP carrier assembly is manufactured by GE Fanuc and has a voltage range of 19.2 to 30 volts DC.

The power rating is 0.22 watts (24 amps) at 5.25 volts DC.

This PROFINET CEP bracket has two Ethernet RJ-45 ports and a Micro-B USB port for firmware.

The IC695CEP001 module is a GE Fanuc CEP carrier module used in GE RX3i systems.

The CEP carrier module is designed for PROFINET communications and has a copper RJ-45 Ethernet port.

The module has 2 Ethernet port connectors with 10/100 Base-TX sockets.

The CEP bracket is a powerful system component with standard functions.

The CEP tray is a powerful system component with standard features such as complete programming and configuration options via Proficy Machine Edition software, and support for multiple network topologies.

USB port for all necessary firmware upgrades, improved troubleshooting and advanced remote node module scanning.

The IC695CEP001 CEP carrier operates over a voltage range of 19.2 to 30 volts DC.

It produces www.cniacs.com 25.0 watts (22.24 amps) of power at a nominal voltage of 5 volts DC.

The system allows one I/O module per station, for a total of 1024 bytes of I/O data per station.

In addition, the GE Fanuc IC695CEP001 carrier module allows up to 512 bytes of I/O data per station for input and output data.

The module supports PROFINET version 2.3 (Class A) and requires Proficy Machine Edition version 8.0 SIM 5 or higher.

The CEP carrier also has 32 input status bits and 32 output control bits.

The IC695CEP001 CEP carrier module is part of a high-speed running I/O LAN system.

The physical characteristics of the IC695CEP001 carrier module include the following dimensions: 177.2 x 51 x 35 mm (7 x 2 x 1.3 inches).

The component operates over a temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).

The IC695CHS007 is a general purpose backplane that is part of the PACSystem RX3i platform, currently part of Emerson Automation and formerly manufactured by GE Intelligent Platforms (GE IP). The backplane has one (1) slot for the IC695 power supply (slot 0) and PCI/serial based IO slots (slots 1-5) and PCI only slot (slot 6). The backplane supports IC695. IC694. and IC693 I/O and option modules or RX3i and 90-30 series modules. The modules are equipped with isolated 24 VDC terminal blocks, grounding points, and internal ground strips.IC695CHS007 is a general purpose backplane for the PACSystem RX3i family of programmable automation controllers (PACs). This backplane is a seven (7) slot backplane reserved for power and I/O modules. It natively supports any IO and option modules of the PACsystem RX3i series as well as the 90-30 series I/O and option modules.

IC695CHS007 Slot 0 is reserved for the IC695 power supply. Slots 1-5 are dual connector slots that support Peripheral Component Interconnect (PCI)-type connectors used by PACSystem components, such as the IC695 module, and serial connectors www.cniacs.com used by the 90-30 series of modules, specifically the IC693 and IC694 modules. Slot 6. the rightmost and last slot, is PCI-only and is compatible with RX3i modules only.

The IC695CHS007 is ideal for applications with limited mounting space or for the implementation of remote I/O architectures. The module comes with a 24 VDC terminal strip located at the left end of the rack. Backplane grounding points and an integrated ground strip are provided for connecting the shielding and grounding connections of the rack-hosted module. The slot number is also clearly printed on this rack so that the module can be installed accordingly.

There are two (2) versions of this IC695CHS007. specifically the initial version, IC695CHS007-AA, and the subsequent version, IC695CHS007-BA, which include mechanical enhancements, specifically the chassis’ backplane PCI connectors.

This IC695CHS007 is for horizontal casting only. Other mounting orientations may affect airflow and ultimately system performance. This rack mounts directly to the chassis panel through the mounting holes provided in the chassis.

– 8 single-ended 4-20 mA input channels

– Non-Flammable Field Circuitry

– HART Direct

– HART variable and status reporting

– 2-wire or 4-wire transmitter

– Open and short circuit detection

– Requires 24 VDC bus field power

Inputs

Number of channels

– 8. single-ended

Nominal Signal www.cniacs.com Range (Scale)

– 4 to 20 mA

Full signal range

– 1 to 23 mA

Line Fault Detection

– Short circuit current – > 23.5 mA

– Open circuit current – < 0.5 mA

Output voltage (@ 20 mA)

-13.5 V (min.)

Output current

– 32 mA (max)

Accuracy (over temperature range)

– ± 0.1% of range

Resolution

– 16 bits

Repeatability

– 0.05 of range

Isolation

– Any channel to rail bus – 100 V ac

– Between channels – none

Configurable parameters

Alarms

– High, High-High, Low and Low-Low

Alarm deadband (hysteresis)

– User-defined values

Hardware Tips and Specifications

While there is not a great deal of factory-released original manual IS215SECAH1A information available online, there is not a great deal of original manual information about the printed circuit board, but some useful material suggests that its status as a solar MACC-BPPB-WEMD component is a strong starting point. Additional information on the series and individual product status of the IS215SECAH1A boards can be obtained by careful visual inspection with a supplementary breakdown of the individualised IS215SECAH1A product numbers. For the uninitiated, two of the more obvious hardware components integrated into the IS215SECAH1A PCB substrate can be recognised in the standard issue Ethernet ports, which are placed longitudinally across each other on the large printed circuit board. Although the IS215SECAH1A board itself contains no other Ethernet ports, the centre of the BPPB board to which it is attached has two identical Ethernet ports. The drive manager has access to eight other ports that connect to this IS215SECAH1A board. These ports are all female and are attached to the edges of the IS215SECAH1A board during factory installation by using screw brackets to improve connection efficiency.

In addition to the various female ports available to users of the IS215SECAH1A board, a series of integrated circuits are integrated into the design of this SECA module. Each of them should be labelled with an individual reference mark, and some of them appear to carry their own factory-applied reference labels with individual component specifications. The final obvious standout hardware feature for the IS215SECAH1A’s circuit board assembly is its series of factory drilled holes. These factory-drilled holes, which are used for mounting purposes, are insulated for complete surface and internal voltage protection, and they are present on the IS215SECAH1A board in a total of five.

While a litany of pertinent information about the IS215SECAH1A printed circuit board is apparent from a simple visual inspection, additional facts about the www.cniacs.com product can be obtained through a simple breakdown of the unique IS215SECAH1A part number, including its special assembly version, SECA functional acronym, and its chemically applied conformal PCB coating protection. Coating Styles.

This IS420YAICS1B modular assembly from General Electric was originally designed and manufactured with the specific functional role of analogue I/O packages in mind for placement within the larger Mark VIe family of turbine control systems.

As its full extended series name implies, the Mark VIe family to which this IS420YAICS1B modular assembly belongs is in the popular, General Electric-compatible wind,

management and control systems for gas and steam turbines.

This is an upgrade to the heavily relied upon Mark V series, which only has specific applications in gas and steam turbine components.

It is a fact that the Mark VIe series, to which this IS420YAICS1B product belongs, is also recognised as the ideal General Electric Mark product family.

This is because it is one of the final GE www.cniacs.com Mark product families to be developed, utilising the patented Speedtronic control system technology that first appeared in the Mark I family introduced in the mid to late 1960s.

Hardware Tips and Specifications

Analogue I/O Pack IS420YAICS1B is part of the Mark VIe series manufactured by General Electric.

This I/O pack allows connection between up to two Ethernet and one terminated analogue I/O board.

The kit can handle up to 10 analogue inputs, two of which can be configured as ±1 mA or 4-20 mA current inputs, and the remaining eight as ±5 V or ±10 V inputs, or 4-20 mA current loop inputs.

The kit can send and receive data over dual RJ45 Ethernet connectors.

For convenience, this IS420YAICS1B I/O package consists of two components; a general processor board and a data acquisition board, as described in the IS420YAICS1B instruction manual that accompanies our manual tab above.

The diagnostic fault detection process for this IS420YAICS1B product is handled entirely through its data acquisition board.

The relevant terminal boards employed in the ruggedly supported modular components of the YAIC analogue I/O kit are the TBAISIC and STAIS2A terminal boards, which are also considered components of the larger Mark VIe turbine control system family.

This IS420YAICS1B device is not actually an original development for its specific Mark VIe Turbine Control System family of features;.

This must be regarded as an IS420YAICS1 parent analogue I/O package, and notably it does not take advantage of the uniquely important Class B functional product revisions of this IS420YAICS1B product.

This DS200SIOBH1ABA General Electric printed circuit board was originally manufactured for General Electric’s Mark V series.

The Mark V series offered by General Electric has specific applications in the management and control systems of gas, steam and wind turbines and is known as the Mark V Turbine Control System Series.

The Mark V series, to which this DS200SIOBH1ABA printed circuit board belongs, is considered to be General Electric’s legacy series.

as it has been discontinued in the years since its original production. Although it is a legacy series of General Electric.

The Mark V series, to which the DS200SIOBH1ABA www.cniacs.com PCB belongs, is one of the most recently developed product lines, utilising GE’s patented Speedtronic technology.

This technology was first introduced in the late 1960’s with the introduction of the Mark I. This DS200SIOBH1ABA PCB is one of the most recently developed product lines. This DS200SIOBH1ABA printed circuit board, or PCB for short, is better known by its official functional product description.

This DS200SIOBH1ABA printed circuit board, or PCB for short, is better defined as a SC2000 VME I/O board by its official functional product description, as shown in the original General Electric and Mark V series instruction manual documentation.

Given this, this DS200SIOBH1ABA printed circuit board is not the original SC2000 VME I/O board that existed in the Mark V turbine control system family; it would be missing this DS200SIOBH1ABA printed circuit board.

This would be missing the extensive revision history of this DS200SIOBH1 parent product DS200SIOBH1ABA PCB.