Category: Nidec

Features

Commissioning

• Power off or on commissioning (even in the box)

• FastStart – assisted commissioning. Only 4 key steps to get up and running

• Easy to use setup tools for: motor settings, speed control, PID controller and

input/output (I/O) functions

• Pre-set application configurations

Cloning

• Parameters can be easily transferred from one drive to another – just tap to

write to as many drives as you want

• Back-up and restore parameter files

Share

• Share parameter files via Outlook, OneDrive, WhatsApp etc

• Shared parameter files are compatible with Marshal and Connect (PC Tool)

• Export parameter files to PDF format

Offline capabilities

• Create new parameter files

• Open existing projects to review/change parameters

Diagnostics

• Diagnostics available with power off or on

• Get support with drive alarms

• Error log & active error diagnostics

• Compare parameter settings to the factory defaults

Monitoring and Security

• Quick view of parameter settings and drive status

• Parameter access can be restricted via a Security PIN

• Quick visualisation of I/O, motor, and speed settings

Product information

Introduction

Commander S100 is a general-purpose drive that delivers maximum

machine performance of induction motors for a range of applications.

The voltage and power rating of the drive should be chosen to suit

the mains supply and the induction motor to be controlled.

The default setting of drive parameters have been selected for the

majority of use cases but can be adjusted to optimize the drive for a

specific application.

The drive is fitted with a terminal cover which will need to be removed

to wire the drive. Re-installing the terminal cover after wiring is optional

on the Commander S100.

Marshal commissioning and diagnostic app

The Marshal app provides a rich interface for commissioning, cloning, and

monitoring the drive. Marshal includes simple tools and setup wizards to

configure the drive for an application and drive diagnostics.

Marshal is for use on smartphones and tablets that support NFC technology

and is available from the Google Play store and the App Store. For details on

compatible phones and using Marshal to commission the drive see section

5.1 Marshal mobile app.

Rugged Die-Cast Aluminum NEMA 4X / IP65 Enclosure with Hinged Cover

Washdown and Watertight for Indoor and Outdoor Use

Primary Features

Horsepower 1/8 to 5 HP, Programmable

115/230/460 VAC-1ph & 3ph Input

Output 230/460 VAC-3ph for AC Induction Motors

Starting Torque 200%

Digital Display with LED Status Indicators

FDA Approved Finish**

GFCI Compatible

Allows equipment to operate

with Ground Fault Circuit Interruption

circuit breakers or outlets.

Benefits

Saves Time

Easy to Install and Simple to Operate.

Does not require commissioning.

With CSP™ you are up and running

in less than 10 minutes.

Motors Last Longer

Proprietary CL Software

Provides overload protection, prevents motor burnout

and eliminates nuisance tripping. UL approved as

electronic overload protector for motors.

Energy Saving

Uses only the power the application requires.

Replacing constant speed with variable speed

will significantly reduce energy costs.

Customization for OEM’s

KBWA

KBWA-22D Non-Vented NEMA 1 / IP 50 Enclosure

KBWA-23D Vented NEMA 1 / IP 20 Enclosure

Primary Features

Horsepower 1/8 to 1/2 HP*

Input 115 and 230 VAC – 1ph

Output 230 VAC – 3ph

Starting Torque 200%

Front Panel Power On/Off Switch

GFCI Compatible

With factory programming, allows the equipment

to operate with Ground Fault Circuit Interruption

circuit breakers or outlets.

Benefits

Saves Time

Easy to Install and Simple to Operate

Does not require programming

or commissioning.

Up and running in less than 10 minutes.

Motors Last Longer

Proprietary CL Software

Provides overload protection, prevents motor burnout

and eliminates nuisance tripping. UL approved as

electronic overload protector for motors.

Energy Saving

Uses only the power the application requires.

Replacing constant speed with variable speed will

significantly reduce energy costs.

Customization for OEM’s

Benefits

Saves Time

Easy to Install and Simple to Operate

Does not require commissioning.

Up and running in less than 10 minutes.

Motors Last Longer

Proprietary CL Software

Provides overload protection,

prevents motor burnout

and eliminates nuisance tripping.

UL approved as electronic overload

protector for motors.

Energy Saving

Uses only the power the application requires.

Replacing constant speed with variable speed

will significantly reduce energy costs.

Customization for OEM’s

When an off the shelf drive does not meet your needs,

KB will work with you to provide a custom drive solution, Ready to Use, “Out-of-the-Box.”

Customization includes: Pre-calibrating or programming of a stock control, adding a custom label or branding,

custom software, PLC functions or designing a new control.

Additional Features

Sensorless Flux Vector Control

Flux Vector Compensation with Static Auto-Tune provides excellent speed regulation

with high torque loads throughout the entire speed range. Auto energy saving at light

loads. Smooth motor torque.

Electronic Inrush Current Limit (EICL™) Protection

Eliminates harmful inrush AC line current during power up.

Ride-Through

Provides smooth recovery to the previous set speed during a momentary power loss.

Holding Torque at Zero Speed

Resists motor shaft rotation when the drive is in “Stop” mode.

Regeneration Protection

Eliminates tripping due to high bus voltage caused by rapid deceleration of high

inertial loads.

Undervoltage and Overvoltage Protection

Shuts down the drive if the AC line input voltage goes above or below

the operating range.

Short Circuit Protection

Shuts down the drive if a short circuit occurs at the motor (phase-to-phase).

Trimpot Adjustments

Min. Speed, Max. Speed, Accel, Decel, Current Limit, Slip Comp.

KBVF

Hybrid Drive™ A Digital AC Drive with Analog Interface

IP20 Enclosure

Primary Features

Horsepower 1/10 to 5 HP

115/230/460 VAC – 1ph & 3ph Input

Output 230/460 VAC – 3ph

200% Starting Torque

Power and Status Indicators

GFCI Compatible

Allows equipment to operate

with Ground Fault Circuit Interruption

circuit breakers or outlets.

(Factory programming required.)

Energy Saving

Uses only the power the application requires.

Replacing constant speed with variable speed

will significantly reduce energy costs.

Customization for OEM’s

When an off the shelf drive does not meet your needs,

KB will work with you to provide a custom drive solution, Ready to Use, “Out-of-the-Box.”

Customization includes: Pre-calibrating or programming of a stock control, adding a custom label or branding,

custom software, PLC functions or designing a new control.

KBVF 4G – NEMA 4X / IP66

Hybrid AC Drives Designed and Customised for PMAC Motors

Our 4th Generation (4G) KBVF Hybrid AC Drives now feature IP66 enclosures suitable for both

indoor and outdoor use. We’ve designed these drives to provide optimum control of with

permanent magnet AC (PMAC) motors, sometimes referred to as either brushless permanent

magnet (BPM) motors or permanent magnet synchronous (PMSM) motors.

The easy-to-install KBVF 4G Hybrid AC Drives are customised to suit requirements for 0.7 – 2.2

kW PMAC motors. Since we typically pre-tune these drives for customer applications, they offer

the convenience of out-of-the-box use.

Common applications for these drives include:

• Agricultural ventilation

• Commercial & Industrial fans and exhausts

• HVAC

• Pumps

• Appliances

KBVF Hybrid Drive – Chassis / IP20

The KBVF Series of Adjustable Frequency Drives consist of sixteen inverter models rated for 

0.07 to 3.7 kW motors. These chassis / IP20 drives are ideal for OEM applications where digital

programming and displays are not required. Hybrid drives are digital drives with an analogue

interface.

Options: SIVFR Signal Isolator and Run Fault Relay (Standard on 460 Vac models), DIVF Modbus

Serial Communication Module, Class “A” or “B” (CE) RFI Filter, DBVF Dynamic Brake Module,

Multi-Speed Board.

KBVF 4G – Chassis / IP20

High-Performance Drives for PMSM Motors

The KBVF 4G (4th generation) drive adds robust PMSM control while keeping its simple and

ready-to-use out-of-the-box interface.

The KBVF 4GChassis / IP20 offers drive solutions for from 0.07 to 3.7 kW in an IP20 package.

AC drives for Commercial Appliances and Machine Integration

KBVF drives are ideal for mounting in appliances, machines and control panels where

digital programming and displays are not required. Ready to use out of the box

customisation is available to meet your specific application needs. Custom KBVF drives

provide the exact drive you need without any unnecessary extras.

KBVF AC drives provide variable speed for 3Ø AC Induction motors from 0.07 to 3.7 kW.

For OEM applications, custom drives are also available for Brushless DC, PMSM, PSC,

and Shaded Pole motors. They are available in 115. 208/230. and 380/460 Vac – 50/60 Hz

with 1Ø and 3Ø input, with optional GFCI / RCD compatible software.

All KBVF AC Drives contain Sensorless Flux Vector Compensation with Static-Auto-Tune.

This provides excellent speed regulation from zero to full load over a wide frequency range.

These drives provide auto energy savings at light loads and smooth motor torque operation.

A variety of optional accessories are also available to meet the most demanding applications.

Features and Specification

Performance

Current loop update time: 62 µs

Heavy load peak rating: 200 % (3 s)

Maximum output frequency: 599 Hz (Open Loop), 550 Hz (RFC-A)

Switching frequency range: 2. 3. 4. 6. 8. 12 and 16 kHz (default 3 kHz)

High performance current controller

On-board intelligence

Programmable Logic Control (PLC)

Real-time tasks

Digital Lock Control

Advanced Motion Controller

On-board communication

Mechanical features

EtherNet (2 switching ports): EtherNet/IP, Modbus TCP/IP, RTMoE and PROFINET RT

Tile mounting on sizes 3. 4. 5

Unidrive SP compatible mechanical footprint

Common DC bus connections