The IC200ALG262 is a component module of the VersaMax I/O platform. It is an analog input module designed to support differential current wiring.

It has eight (8) analog input channels designed to receive standard current input signals such as 0-20 mA and 4-20 mA input signals.

This IC200ALG262 is currently manufactured by Emerson Automation. It is ideally suited for connection to analog signal generating instruments such as field transmitters.

for measuring pressure, level, flow, temperature, turbidity, viscosity, speed, and other types of transmitters; for integrating locally mounted panel meters to

remote display; for monitoring the speed output of variable frequency drives (VFDs); for monitoring the position of rotary and linear devices; and other applications.

The IC200ALG262 has a built-in analog-to-digital converter (ADC) circuit with 15-bit conversion resolution. The input channels are arranged in groups.

When configured to receive 4-20 mA, they are capable of detecting power loss and open circuit detection within the module. Each channel has an uplink rate of 7.5 ms.

Each channel has an uplink rate of 7.5 ms and a digital resolution of 0.5 μA (4-20 mA signal range) and 0.625 μA (0-20 mA signal range). The module has a maximum backplane current consumption of 5 mA at 200 VDC bus voltage.

Compatible configuration software and hardware firmware versions that can be used with this module include VersaPro software version 2.0 or later; VersaMax PLC CPU CPU version 2.0 or later; and VersaMax PLC CPU version 2.0 or later.

​This IC695RMX128 is a PACSystems RX3i redundant memory switching module manufactured by Emerson Automation (formerly GE Intelligent Platforms (GE IP)).

The module has 128MB of SDRAM user memory and supports operation as a reflective memory network or dedicated link between RX3i CPUs in a redundant configuration.

The module comes with single-mode fiber that supports 2.12 Gbaud fiber networks.

About the IC695RMX128

The IC695RMX128 is the PACSystems RX3i Redundant Memory Exchange Module.

The primary function of the module is to act as a single node on a reflective memory topology or as a dedicated memory module for redundant RX3i CPU pairs.

When used in a redundant CPU configuration, the IC695RMX128 reflects the contents of the IC695CMX128.

With a reflected memory link, any updates on one node are reflected and updated to all other nodes connected to the same network.

Connections are established over a fiber optic network supporting up to 256 nodes.

The module is equipped with 128 MB of reflective memory, and the fiber optic power supply requires an LC-type connector for transmission speeds up to 2.12 Gbaud.

The module operates on supplies of 580 mA @ 3.3 VDC and 220 MA @ 5 VDC.

Features:

. Direction of each 8-bit port is individually programmable

.64 mA sink current capability (15 mA source) .

. Separate board address decoding for control and data registers .

. Built-in test logic for fault detection and isolation .

. Highly reliable DIN-type I/O connectors .

. 8-bit, 16-bit, 32-bit transfers

The VMIVME-2510B is a member of the VMIC Megamodule family, which is designed for universal programming.

The subsystem can be configured with consecutive www.cniacs.com I/O addresses to conserve memory.

These products (VMIVME-1110. VMIVME-2120. VMIVME-2130. and VMIVME-2510B) are designed with two sets of board address switches to provide efficient memory address mapping for CSR and I/O addresses.

The CSR address switches can be configured so that all CSRs on the various boards in the system can be mapped to contiguous memory locations.

Megamodule products are also designed to support 8-bit, 16-bit and 32-bit data transfers.

Specific hardware has been designed into the VMIVME-2510B to support the built-in test functions.

The VMIVME-2510B supports off-line and on-line fault detection and isolation. The front panel Fail LED is used to indicate when a fault exists on this board.

The LED is illuminated at power-up or reset. The LED can be turned off after successfully completing board level diagnostics.

The 169PLUS-120N-125VDC is a highly configurable motor protection system manufactured by General Electric Multilin.

The relay comes with basic setpoints programmed for large motor systems, which can be further adjusted by the user upon receipt of the relay or as they become more familiar with the data generated by the relay.

While users can manage their motor systems with fairly minimal connection to GE Multilin’s 169PLUS-120N-125VDC.

However, the unit does offer a wide range of ports to diversify and customize the function of the relays.

Some of these connections include:

. Auxiliary Relay Contacts: these two contacts provide an additional NO/NC connection and operate independently of the other contacts.

The relays can be configured as non-fail-safe or fail-safe, and latching or non-latching.

They can be used for active alarm or trip functions and can trigger devices that are not just motors.

RTD Sensor Connections: The user can connect up to 6 resistance temperature detectors.

This is used to monitor values such as stator motor temperature, historical hottest temperature and ambient air temperature.

The relay then uses the data obtained from these connections to schedule the optimal cooling process.

. Analog output terminals: These two terminals can be configured using the relay’s setpoint system.

It can be connected to chart recorders, remote meters, programmable recorders and/or computer loads.

. Emergency Restart Terminal: This connection type overrides trips within the system and forces a restart of the motor.

These connections add to the overall versatility of the system and can further protect motor components from damage during operation.