Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0
April 27, 2025 BY
IN Advantest

Advantest Q7750 Optical Oscilloscope (Optical Network Analyzer)

The Q7750 optocope (optical network analyzer) is a revolutionary device for measuring optical transmission characteristics.

It can measure the amplitude/dispersion/group delay characteristics of incident and reflected light from optical devices at high speed and high resolution over the optical carrier frequency range.

In addition, it can easily measure various chromatic dispersion characteristics, including the zero-dispersion characteristics and dispersion slope characteristics of dispersion-shifted or non-zero-dispersion fibers.

Measurement using the phase-shift method enables high optical frequency resolution and wide dynamic range.

Batch Measurement of Optical Transmission Characteristics in the Optical Carrier Frequency Range The Q7750 is equipped with a variable wavelength light source.

The Q7750 is equipped with a variable wavelength light source that enables simultaneous measurement of transmission and reflection characteristics in the optical carrier frequency range by scanning a series of wavelengths (optical frequencies) (S21 and S11 as S-parameters).

The measurement parameters are shown in the table below. These parameters can be measured simultaneously in a single scan.

High optical frequency resolution

Optical frequency resolution: up to 50 MHz (converted to 0.4 pm according to wavelength)

The Q7750 has a maximum optical frequency resolution of 50 MHz, which enables measurements in the field of ultra-high-resolution optical carrier frequencies that were not previously possible.

Amplitude and chromatic dispersion characteristics of optical devices for DenseWDM or Ultra-Dense-WDM can be easily measured (channel steps: 100 GHz, 50 GHz, 25 GHz, etc.).

Selectable wavelength spans from 70 nm (maximum) to approximately 0.1 nm (minimum).

High-speed measurement

Measurement time Approx. 6.7 ms (per measurement point) Approx. www.cniacs.com 4 seconds (within the specified span) The interval between scans (measurement time) is approx. 4 seconds.

This means that the Q7750 can complete a measurement in 4 seconds, whereas the previous measurement process took several tens of seconds.

If the measurement time is too long, accurate results may not be obtained because the characteristics of the device under test may change due to environmental conditions such as temperature.

The Q7750 completes measurements in a short period of time, ensuring high-speed, accurate measurements that are unaffected by the temperature characteristics of the device under test.
April 27, 2025 BY
IN Advantest

Advantest Q8383 Optical Spectrum Analyzer

Key Features

– Sensitivity -92 dBm

– Polarization correlation ±0.05 dB

– Resolution bandwidth accuracy ±2

– Power Measurement

– Pulsed light measurement

Operation

In addition to amplifier analysis, a variety of display modes are available, such as

– Overlay display,

– Comparison with memory contents,

– Display of two independent graphs (split screen),

– Power meter function,

– Use of multiple markers,

– Normalized and direct readout of transmission loss and

– Automatic bandwidth analysis (e.g. measurement of half-value widths based on RMS and envelope methods),

– Curve fitting over the IEC/IEEE bus and many other features facilitate operation of the analyzer and simplify analysis.

A standard internal disk drive is used as a storage medium. Stored binary data can be analyzed with the appropriate program under MS-Windows or copied to a file and printed out.

The high-speed built-in thermal printer prints out a hard copy of the measurement results with all setup parameters in less than 10 seconds. The built-in high-speed thermal printer prints a hard copy of the measurement results with all setup parameters in less than 8 seconds.
April 27, 2025 BY
IN ABB

ABB CM10 Universal Process Controller

ControlMaster CM10 is a flexible 1/8 DIN general purpose PID process controller.

The ControlMaster CM10 is a flexible 1/8 DIN general purpose PID process controller.

The CM10’s full-color TFT display clearly shows detailed process information and its intuitive operator interface simplifies configuration and operation.

The CM10 is expandable in both hardware and software functionality to easily meet your application needs.

The CM10’s flexible control features, including on/off, time proportioning, analog PID, split output control, and math logic, make it suitable for a wide range of process applications.

Fully configurable via easy-to-navigate front panel menus or PC configuration software, the CM10 can be quickly commissioned and then adjusted via advanced auto-tuning features.

MODBUS and Ethernet communication options ensure easy integration into control systems.

The CM10 is equipped with a 5.5 cm (2.2 in.) full-color display for showing detailed process information to the user.

Process details such as alarms and diagnostic information are clearly displayed in full text without the need for hard-to-read scrolling.

Example of an operator’s page

Automatic selection of standard display templates immediately makes full use of the CM10’s display. Extensive customization capabilities allow the information displayed to be tailored to the process requirements.

Diagnostic and Alarm Status Display

The Diagnostics and Alarm Status Display provides detailed information on any active alarms or diagnostic conditions. The operator can see at a glance any alarm conditions present in the process.

In addition, diagnostic information is clearly displayed www.cniacs.com to the operator for quick notification and simple diagnosis of any critical instrument status.

Exceptionally easy to use

The CM10’s full-text display and easy-to-navigate pop-up menus make operation exceptionally easy.

With programmable soft keys, operators can easily access frequently used functions such as auto/manual selection, alarm acknowledgement and display selection.
April 27, 2025 BY
IN Motorola

Motorola MVME333-2 Controller Communication Module

Features:

6 serial I/O ports

Supports synchronous and asynchronous communication

128 Kb of dynamic RAM

High-speed bi-directional DMA on two channels

The Motorola MVME333S-2 is a VMEbus intelligent communications controller with six serial I/O ports that can be configured for synchronous or www.cniacs.com asynchronous and RS-232C or RS-422 electrical protocols.

On-board intelligence includes the MC68010 10 MHz CPU with two slots for firmware and 128 Kb of dynamic RAM for data buffering.

It has firmware for asynchronous protocols on all six channels (up to 9600 baud in both directions on all channels simultaneously).

In addition, there is a high-speed bi-directional DMA for synchronous protocols up to 1 Mb/s on two channels.
April 27, 2025 BY
IN ABB

ABB CM-TCS Temperature Monitoring Relay

The temperature monitoring relay CM-TCS monitors over-temperature, under-temperature or temperature between two thresholds (window monitoring) via a PT100 sensor.

As soon as the temperature falls below or exceeds the threshold, the output relay changes position according to the configured function and the LED display on the front shows the current status.

All devices are available in two different terminal versions. You can choose between the proven screw connection technology (dual-chamber cage connection terminals) or the completely tool-free easy connection technology (push-in terminals).

Features

Configurable over-temperature monitoring, under-temperature www.cniacs.com monitoring, temperature window monitoring, etc.

All configurations and adjustments via front-operated elements

Precise adjustment via direct reading scale

One or two thresholds

Hysteresis 2-20 % adjustable

Operating temperature range -40… +60°C

Open or closed circuit principle configurable

Short-circuit monitoring and wire break detection

Screw connection technology or simple connection technology possible

Housing material according to the highest fire protection class UL 94 W-0

DlN rail mounting and dismounting without tools

1 x2 co or 2×1 c/o (SPDT configurable)

22.5 mm (0.89 in) wide

3 LEDs to indicate operating status
April 27, 2025 BY
IN ABB

ABB CM-IWx Insulation Monitoring Relay

Reliable insulation monitoring of IT systems

CM-IWx insulation monitoring relays ensure continuous insulation monitoring of IT systems to minimize equipment downtime.

ABB’s CM-IWx insulation monitoring relays for IT systems provide continuous, reliable monitoring.

These devices recognize an insulation fault as it develops and trip once the value falls below a minimum set threshold.

This makes the system more reliable and prevents interruptions caused by severe secondary insulation faults.

Make your monitoring safer and your maintenance smarter with the CM-IWx insulation monitoring relay.

Continuous operation

Reduce downtime with early warning

More time for planned maintenance

Early fault detection by monitoring voltage-free networks

Railroad and marine approved models available

Safety and Protection

Safe and reliable insulation fault detection

Compliance with the latest standards

Solutions for standard and challenging applications

Fast and reliable earth fault detection supports fire protection

Self-diagnostics and wire break detection

Easy to install

Clear indication of device status via LEDs

Easily adjusted using a rotating wheel

Push-in terminals

Features

System voltage monitoring up to 1500 V DC and 1100 V AC

System leakage capacitance monitoring up to 3000 μF

Versatile system monitoring for 2-wire, 3-wire, www.cniacs.com 4-wire and battery systems

Easily configurable wire break detection

Easily configurable non-volatile fault storage
April 27, 2025 BY
IN ABB

ABB CM-TCN Intelligent Temperature Monitoring Relay

Device Overview

The CM-TCN Smart Temperature Monitoring Relay is designed to meet different customer needs with one device.

Its LCD display provides intuitive status updates, and through Near Field Communication (NFC) you can adjust settings simply from your smartphone, making installation quicker and more intuitive.

With a measuring range of -200…+850 °C, the device is compatible with a wide range of sensor types and offers storage for predefined and user-defined configurations for common motor or transformer monitoring applications.

Wireless configuration and status checking is possible using ABB’s EPiC application.

Using the app, parameters can be quickly set and stored in the app or copied to other CM-TCN devices, even in the absence of power.

In addition, parameters can be uploaded to the www.cniacs.com cloud or shared via email within seconds.

Temperature monitoring relays are typically used in the following applications:

Motor and system protection

Control cabinet internal temperature monitoring

Motor monitoring

Transformer monitoring

Ambient temperature monitoring

Process variable temperature limits

Bearing temperature monitoring

Coolant Temperature Monitoring

Packaging Industry

Air conditioning systems

Ventilation systems

Heat pumps

Hot water supply

LCD display and symbol-based menu structure

Unit with LCD display.
April 27, 2025 BY
IN Motorola

Motorola 3496B01A MVME712M/M P2 Adapter Board

Features:

4 25-pin multi-protocol EIA-232-D serial ports

The MVME712M is an I/O converter module for Motorola MPU VME Modules, VME Processor Modules, Embedded Controllers, and Single Board Computer (SBC) series processor modules.

The MVME712M is compatible with the MVME147. MVME1600. MVME162. MVME2600. MVME167. MVME2700. MVME177. MVME3600. MVME4600.

The MVME712M is used as an interface between the processor module and its peripherals. The purpose of this module is to provide rear panel industry standard connectors to simplify external customer cable requirements.

Features:

4 25-pin multi-protocol EIA-232-D serial ports

The MVME712M is an I/O converter module for Motorola MPU VME Modules, VME Processor Modules, Embedded Controllers, and Single Board www.cniacs.com Computer (SBC) series processor modules.

The MVME712M is compatible with the MVME147. MVME1600. MVME162. MVME2600. MVME167. MVME2700. MVME177. MVME3600. MVME4600.

The MVME712M is used as an interface between the processor module and its peripherals. The purpose of this module is to provide rear panel industry standard connectors to simplify external customer cable requirements.
April 27, 2025 BY
IN Motorola

Motorola PPMC750-1141 Processor PCI Mezzanine Card

PPMC750-2xxx Description

The PPMC750-2xxx is an extended form factor version of the PPMC750 Processor PCI Mezzanine Card (PPMC) board (see the Processor PMC Standard for VITA-32-199x Processor PCI Mezzanine Cards for more information).

The PPMC750-2xxx is 1.5 times wider than normal at 111 mm. It is based on the PowerPC MPC750 processor and the Hawk PCI host bridge/system memory controller.

Standard features of the PPMC750 include 1MB of L2 cache, an on-board bank of SDRAM (32MB to 128MB), 8MB of FLASH, and optional SDRAM memory expansion.

In addition to the standard features of the PPMC750. the PPMC750-2xxx features 1MB of socketed FLASH, a 10/100TX Ethernet channel, a 190-pin Mictor debug connector, and a serial port debug connector.

Four 64-pin PMC connectors on the PPMC750-2xxx are used to connect the PPMC750-2xxx to the motherboard.

A 10-pin right-angle connector located on the side of the motherboard provides the interface to the asynchronous serial port. A 16-pin header provides the interface to the processor’s JTAG/COP port.

A 190-pin Mictor connector on the secondary side of the www.cniacs.com board provides debug access to the processor bus.

The serial port and JTAG/COP interfaces and ABORT_L signals are also routed to the PMC P14 connector for access to the carrier board.

The PPMC750-2xxx includes a 140-pin AMP connector mounted on the auxiliary side of the board to provide sockets for memory expansion functions.

The presence of this connector increases the height measurement of the components on both sides beyond the standard PMC height.

Monarch and Non-Monarch PPMC

The traditional concepts of host/master and slave/target processors changed with the creation of the PPMC because the arbiter or clock source traditionally located on the host board was not on the PPMC7502xxx.

The VITA 32 specification defines the terms Monarch and Nonmonarch to refer to the two modes of PPMC operation.
April 27, 2025 BY
IN Motorola

Motorola MVME162FX Embedded Controller

The MVME162FX is based on the MC68040 or MC68LC040 microprocessor.

Different versions of the MVME162FX are available with 4MB, 8MB or 16MB of unprotected DRAM, 8KB SRAM (with battery backup), daily clock (with battery backup),

Ethernet transceiver interface, two serial ports with EIA-232-D or EIA-530 or EIA-485/422 interfaces, six timers, watchdog timer, one PROM socket,

1MB of Flash memory (one Flash device), four IndustryPack (IP) interfaces with DMA, SCSI bus interface with DMA, VMEbus controller, and 512KB of SRAM with battery backup. a “no VMEbus” option is also available.

The I/O on the MVME162FX is connected to the VMEbus P2 connector. The main board is connected via a P2 transition board and a cable connecting the transition board.

The MVME162FX supports the transition boards MVME712-12. MVME712-13. MVME712M, MVME712A, MVME712AM, and MVME712B (referred to in this manual as MVME712x unless otherwise noted).

The MVME712x transition board provides configuration headers and industry standard connectors for I/O devices.

I/O connections to the serial ports on the MVME162FX www.cniacs.com are also made via two DB-25 front panel I/O connectors.

The MVME712 series transition boards are designed to support the MVME167 boards, but can be used on the MVME162FX if some special precautions are taken.

(For more information, see the Serial Communications Interfaces section of the MVME162FX Embedded Controller Installation and Use Manual).

These transition boards These transition boards provide configuration headers, serial port drivers, and industry-standard connectors for I/O devices.

These transition boards provide configuration headers, serial port drivers, and industry standard connectors for I/O devices.

Benefits

The MVME162FX series provides an ideal platform for embedded monitoring applications for OEMs and solution developers.

It enables OEMs to minimize engineering costs while integrating value-added hardware and software applications into off-the-shelf products.

To provide a wide range of solutions, the MVME162FX allows the use of a variety of MPUs, memory and interface options such as floating point, Ethernet, SCSI and VME.

As a result, the MVME162FX variants best fit the application requirements.

Menu

Search for products

Back to Top
Product has been added to your cart