Category: A-B

About the 1336E-B030-AN-EN-GM1-HA2-L7E

The 30 hp 1336E-B030-AN-EN-GM1-HA2-L7E drive is an Allen-Bradley AC drive that is part of the Allen-Bladley 1336 IMPACT product family.

For the Rack C 1336E-B030-AN-EN-GM1-HA2-L7E drive, the outputs and inputs are connected to TB1. which is the 11-position terminal block on the gate drive board.

National wiring codes should be considered during wiring to minimize the risk of injury and equipment damage.

The drive control interface supports TTL contacts. Encoder feedback is also provided on the drive.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive is available with an output power of 22 kW or 30 hp at 380 to 480 volts AC input voltage.

Output current and apparent power ratings are 48.2 amps and 38 kVA, respectively.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive draws 49 amps and 32 to 41 kVA at the input.

The input and output frequency ranges are 47 to 63 Hz and 0 to 250 Hz, respectively.

The driver output is capable of sustaining 100% of the rated current continuously or 150% of the rated current for up to 1 minute.

The maximum short circuit rating is 200.000 amps RMS symmetrical. The HMI is part of the standard driver package, which includes the controller and programmer.

Digital potentiometers are also available on the driver. The drive has an English language module. For network communications, the drive has a single point remote I/O interface.

The 1336E-B030-AN-EN-GM1-HA2-L7E drive is an open drive with an IP00 enclosure.

The recommended operating ambient temperature range is 32 to 122 degrees Fahrenheit. The drive has a shipping weight of 38.6 kg.

The dimensions of the drive rack are 701 x 301.8 x 225.0 mm.

1336E-B030-AN-EN-GM1-HA2-L7E Technical Description

The Allen-Bradley® Stratix® 5800 managed industrial Ethernet switch delivers Gigabit performance in a flexible package.

Its fixed and modular design supports a variety of copper, fiber, and PoE expansion modules, and offers Layer 2 switching or Layer 3 routing firmware options to meet a variety of application needs.

When used as a Layer 2 switch, the Stratix 5800 is ideal for high-performance end devices.

When used as a Layer 3 switch, routing can be enabled between segmented networks to improve performance and prevent unwanted network traffic.

Network segmentation helps simplify security management by establishing trust domains and improving efficiency.

The Stratix 5800 includes a robust set of switching, routing, and security features to support a wide range of architectures and uses the Cisco IOS-XE operating system to optimize compatibility with enterprise environments.

Choosing a switch co-developed by Rockwell Automation and Cisco allows your operations technology (OT) and information technology (IT) professionals to leverage the tools and techniques they are familiar with.

By helping to provide optimized integration, you can experience easier commissioning and actionable diagnostics.

Features and Benefits

– Full Gigabit switch platform High-performance networking support

– Fixed and modular options with up to 26 ports for flexibility and scalability

– Multiple copper, fiber and PoE options to support a variety of applications

– Supports Layer 2 access switching and Layer 3 routing for use in multi-tier architectures

– Supports IT and OT configuration and management tools, enabling users to leverage the expertise of both teams

– Provides default configurations for industrial applications for easy setup and optimized performance

– IEC 62443-4-2 certified for compliance with global cybersecurity standards

Optimized integration

– Studio 5000® Add-On Profiles (AOPs) enable optimal integration with Rockwell Automation® Integrated Architecture® systems.

Integration into Rockwell Automation® Integrated Architecture® Systems

– Predefined named Logix tags for monitoring and port control

– FactoryTalk® View panel for status monitoring and alarming

– Embedded Cisco® technology, including the IOS-XE operating system, facilitates secure integration with corporate networks

Our Kinetix® 5700 servo drives are designed for machines with large axes and high power requirements.

These high-performance servo drives utilize leading-edge technology designed to help you build machines that are more capable, more flexible, and more energy efficient than ever before.

The Kinetix 5700 servo drives utilize EtherNet/IP communication technology that

Complete your Logix control system with fast access to the data you need, while simplifying your system by using one network to integrate motion and safety functions.

New Features

Tuning-Free Startup and Operation

The Kinetix 5700 server’s V13 firmware has updated features that reduce or eliminate debugging efforts.

Enhancements include.

Virtual Torque Sensor feature detects anomalies and provides analysis

Adaptive tuning now includes multiple tracking trap filters and improved filter configurations.

Command trap filters reduce load oscillation in applications without load sensors

Supports 200V and 400V rated motors

OVERVIEW

High-performance Kinetix 5700 servo drives help meet the demands of demanding applications in a wide range of industries.

These multi-axis servo drives combine high-performance servo and vector motor control to help simplify machine design and reduce the time and labor costs required for integration.

Kinetix 5700 servo drives can be configured with integrated drive safety and regenerative bus power to help make your next servo solution safer and more energy efficient than ever.

Functional Features

Kinetix 5700 Servo Drive

Delivers high power density in a compact rack size

Offers a wide power range of 1.6…. .112 kW wide power range

Supports servo and induction motors with a wide range of feedback types

Features a dual-axis module

Innovative snap-in bus system for easy assembly and installation

Supports single-cable solutions for motor power and feedback

Includes dual Ethernet ports to support linear and device level ring (DLR) topologies

CIP security features support defense-in-depth approach to network security

Kinetix 5700 Integrated Safety Servo Drive

Includes integrated or hard-wired safety options

Integrated safety option reduces overall system wiring

Advanced safety features with Safe Torque Off, Safe Stop and Safe Monitor functions

The 2198-S160-ERS3 has a three-phase power output of 60.1 KW, an internal capacitance of 1120 μF, and requires 92.3 A DC input current at 458-747 V DC.

When the servomotor connected to the inverter does not have a holding option, the inverter has a control current of 4.6A at 24V DC supply.

The inverter also has a control current of 9.6A at 24V DC if the servomotor has braking enabled,.

And the inverter will receive 4A inrush current under 24V DC.

The 2198-S160-ERS3 has an operating heat sink relative to the percentage of rated output power of the inverter of

270W at 20%, 420W at 40%, 570W at 60%, 760W at 80%, and 950W at 100% of utilized output power.

Motor feedback and auxiliary feedback are provided via a 15-pin universal feedback connector (UFB) and a 2-pin motor feedback connector (MF).

and is pre-installed with an EtherNet network connection port.

The 2198-S160-ERS3 has an operating temperature range of 0-50°C (32-122°F), a non-condensing relative humidity of 5-95%, and a storage range of -40-70°C (-40-158°F).

It has a mounting height of 1500 meters (4921 feet), is not rated, and can withstand 15G operational shock and 2G vibration from 55-500Hz.

It is c-UL, CE, KC, c-TICK, ODVA, and OSHA certified and has an IP20 protected enclosure.

The 2198-S160-ERS3 weighs approximately 6.8Kg (15 lbs) and measures approximately 252mm x 478mm x 100mm (9.92″ x 18.82″ x 3.94″).

The 1756-IF4FXOF2F is a ControlLogix discrete high-speed analog I/O module.

It has four (4) high speed, sub-millisecond, differential inputs and is compatible with input signals ranging from ± 10V 0…. .10V 0… .5V 0… .20 mA.

It also has two high-speed voltage or current outputs with an output signal range of ± 10V 0…. .20 mA.

About the 1756-IF4FXOF2F

The Allen-Bradley 1756-IF4FXOF2F is an analog combo I/O module.

The module is part of the ControlLogix system and is compatible with the 1756 ControlLogix chassis, which requires the 1756-TBS6H or 1756-TBCH removable terminal block enclosure (RTB).

The module has four sub-millisecond high-speed differential inputs and two high-speed voltage or current outputs.

The module has a display that shows the module’s health and operating status (e.g., calibration mode).

The 1756-IF4FXOF2F has input ranges of +/-10 volts, 0 to 10 volts, 0 to 5 volts, and 0 to 20 milliamps, and displays over-range when the module is out of these ranges.

Overvoltage protection is 30 volts DC and 8 volts AC/DC. Its open circuit detection is a positive full scale reading within 1 second.

The module has an output range of +/-10 volts, 0 to 20 milliamps, and short-circuit protection, limiting the electronic current to 21 milliamps or less.

It also has 24-volt DC overvoltage protection and open-circuit detection, but is limited to current outputs only (note that outputs must be set to greater than 0.1 mA).

The 1756-IF4FXOF2F has backplane voltage and current ratings of 375 milliamps (at 5.1 volts DC) and 100 milliamps (at 24 volts DC).

The analog inputs and outputs are rated at -10 to 10 volts and 4 to 20 mA, respectively.

Module power consumption is 4.3 watts with 4.3 watts of voltage dissipation and 4.7 watts of current dissipation.

Thermal dissipation is 14.66 BTU/hr for voltage and 16.02 BTU/hr for current.

Current consumption is 375 mA at 5.1 volts and 100 mA at 24 volts.

It has a scan time update cycle of 300us minutes with sub-millisecond channel scanning and multi-module synchronized sampling.

The Allen-Bradley 1756-IF4FXOF2F is a ControlLogix high-speed analog combo module.

The module features four (4) high-speed, sub-millisecond differential inputs that accept ± 10V, 0 to 10V, 0 to 5V, and 0 to 20 mA signal ranges.

Each analog input channel has integrated over- and under-range indication. It is also equipped with two (2) high speed voltage or current output channels with output ranges of ± 10V and 0 to 20 mA.

The Allen-Bradley 1746-NT8 is an SLC 500 thermocouple/mV analog input module.

The module has eight (8) channels and is compatible with thermocouple sensors such as J, K, T, E, S, R, B, and N. It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV.

It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV. The module is compatible with both stationary and modular SLC 500s.

About the 1746-NT8

The 1746-NT8 is Allen-Bradley’s SLC 500 thermocouple/voltage analog input module.

It is a chassis-mounted, eight (8) channel module that receives thermocouple/voltage signals and converts them to digital signals for retrieval by any SLC 500 processor.

It has a backplane current rating of 120mA at 5V DC and 70mA at 24V DC for a total backplane power of 2.28W.

The 1746-NT8 uses a delta-sigma signal conversion method and has a digital low-pass filter with selectable programmable filter frequencies.

The normal mode rejection between terminals is greater than 100 dB at 50-60 Hz, and the common mode rejection between input and ground is greater than 100 dB at 50-60 Hz.

The 1746-NT8 module automatically calibrates itself approximately every 2 minutes after power-up.

It provides +/-30V DC and 600W pulses for 1ms input overvoltage protection and 12.5V DC circuit isolation between inputs and chassis ground, and between inputs and backplane, with a test voltage of 500V DC for 1 minute.

The 1746-NT8 has nine green LEDs to indicate channel status and module status.

It uses the 1746-RT34 (RTB) removable terminal block to connect the input devices. The terminal block includes two (2) cold junction compensation (CJC) sensors with an accuracy of +/-1.72 degrees Celsius.

The 1783-MX08T switch is an Allen-Bradley managed Ethernet switch.

About the 1783-MX08T

The 1783-MX08T Switch, manufactured by Allen-Bradley, is a Stratix 8000 modular managed Ethernet switch.

The managed switch has up to eight ports and is powered from 24 to 48 V DC.

The 1783-MX08T switch provides an optimized solution for both IT and manufacturing environments.

The Allen-Bradley Stratix 8000 Managed Modular Switch is jointly manufactured by Rockwell Automation and Cisco.

The 1783-MX08T switch features a user-friendly interface that ensures users have an easy installation process and a simple control environment.

In addition, the 1783-MX08T switch supports the RXLogix 5000 operating environment as well as diagnostic panels to further simplify use.

The 1783-MX08T switch is designed to provide simple and secure integration with the corporate network.

 This is accomplished through the CIP interface, which allows integration with enterprise-connected devices.

The Allen-Bradley 1783-MX08T switch measures 112 mm in length, 97 mm in width, and 147 mm in height.

The recommended ambient operating temperature range is -40 to 60 degrees Celsius. 

The ambient storage temperature range is -40 to 85 degrees Celsius and the relative humidity is rated at 5% to 95% non-condensing.

The 1783-MX08T switch has an open housing and supports an inrush current rating of 2 amps.

The unit utilizes a 10/100 Base T Cooper Ethernet port. The supported memory type is CompactFlash memory.

The 1783-MX08F Switch is an Allen-Bradley network switch. The module is an 8-port switch with 100 Base-F fiber optic Ethernet ports.

About the 1783-MX08F

The 1783-MX08F Switch, manufactured by Allen-Bradley, is an 8-port Stratix 8000 switch.

The 1783-MX08F switch has a supply voltage of 24 to 48 volts DC and a power dissipation of 10.1 watts.

The Allen-Bradley Stratix 8000 switch has an open enclosure and uses 100 Base-F fiber optic Ethernet ports.

Modules are of the CompactFlash memory type and are rated at 2 amps inrush current.

The 1783-MX08F switch is 112 mm long, 97 mm wide, and 147 mm high.

To ensure optimal performance, it is recommended that users ensure that the ambient operating temperature range is between -40 degrees Celsius and 60 degrees Celsius.

The 1783-MX08F switch has a relative humidity range of 5% to 95% (non-condensing) and a maximum operating vibration of 2 G at 10 to 500 Hz.

It is rated for 20 G of operating shock and 30 G of non-operating shock.

The Allen-Bradley 1783-MX08F switch supports fiber optic Ethernet data rates of 100 Mbps.

The 1783-MX08F switch is optimized for IT and control/manufacturing control environments.

This makes the 1783-MX08F switch a high-performance managed Ethernet switch.

The 1783-MX08F Switch combines Cisco technology with innovative Allen-Bradley/Rockwell Automaton technology for high performance.

The 1783-MX08F switch is easy to set up and enables comprehensive diagnostic information within the specified Allen-Bradley/Rockwell Automation integrated architecture.

The 1783-MX08F switch provides users with the benefits of a CIP interface with predefined Logix tags and advanced configuration screens.

The Allen-Bradley 1771-IR is a PLC5 resistance temperature detector (RTD) input module.

The module has six (6) input channels and is compatible with copper and platinum RTD types.

It is designed to support temperature measurements in Celsius and Fahrenheit units of measurement. It has a scan time of 50 milliseconds for six channels.

About the 1771-IR

The Allen-Bradley 1771-IR is a PLC-5 RTD input with a natural binary BDC supported data format for actual temperature and ohmic readings.

The unit does not require any type of external power supply. It consists of six three-wire RTD inputs.

The device’s channel update resolution introduces a combination of 50ms/6 channels and 16 bits + sign (1.0 degrees Celsius/1.0 degrees Fahrenheit/bit).

The 1771-IR input module has a voltage range of 100 ohms platinum and 10 ohms other. It has a backplane current range of 800mA.

The DC signal delay is 10ms in the on state, 50ms in the off state, and 45(+/- 15) ms in the AC signal delay in the on state.

These input modules have a lifetime of up to 100 million cycles as they meet voltage requirements of 10-276V AC.

The 1771-IR also helps protect your system by providing appropriate troubleshooting assistance. Module indicators show the status of smart inputs or outputs to help you troubleshoot your equipment.

The 1771-IR has an intelligent hybrid interface for connecting on/off devices such as switches, motor starters, pushbuttons, indicators and signalers.

This unique feature helps save on system engineering and spare parts as well as inventory and training costs.

The front panel of each AC discrete input/output module consists of bright status indicators.

The 1771-IR supports both Celsius and Fahrenheit measurement units. The platinum sensor has a temperature measurement range of -200 to +870 degrees Celsius and the copper sensor has a temperature measurement range of -200 to +260 degrees Celsius.

It has a resistance range of 1.00 to 600.00 ohms and a resolution of 0.1 degrees Celsius or 0.1 degrees Fahrenheit when used with a platinum sensor and 0.3 degrees Celsius or 0.5 degrees Fahrenheit.

Description: Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive component.

The Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive assembly.

It is a 400VAC rated shaft module with a continuous current of 6.1 A and a peak current of 15.3 A. It has a 98% efficiency and a symmetrical 200.000 A (rms) short circuit current rating.

It has 98% efficiency and a symmetrical short circuit current rating of 200.000 A (rms).

About the 2094-BM01-M

The 2904-BM01-M is an Allen-Bradley component designed for use with Kinetix 6000 drives.

The drive is used as an axis module (AM), is in the 400 VAC voltage category, and has a continuous current of 6.1 A and a peak current of 15.3 A. The drive is designed for use with Kinetix 6000 inverters.

The 2904-BM01-M mounts directly to the Kinetix drive power rail. It is typically mounted next to the Integrated Axis Module (IAM) along the power rails, where the module draws power from the power rails to power its internal circuitry.

The axis module connects to the motor and motion device via feedback cables, auxiliary feedback cables, I/O, and safety wiring.

Axis modules also allow the installation of a control module so that control inputs can be integrated into the module.