Category: ABB

The INIIT12 module is a single printed circuit board that occu

pies one slot in the module mounting unit, adjacent to its NIS

module. The circuit board contains the serial communication

circuitry necessary for it to communicate with another INIIT12 module.

Two captive latches on the INIIT12 faceplate secure the module

in the MMU card cage. The faceplate contains eight CPU LEDs,

a red/green status LED, and a stop/reset switch.

Interface termination is through a cable connection between

P3 of the INIIT12 module and an NTMP01 Multi-Function Pro

cessor Termination Unit or NIMP01 Multi-Function Processor

Termination Module. INIIT12 module power and I/O expander

bus connections follow the same connector assignments com

mon to most INFI 90 OPEN modules (P1 for power, P2 for I/O expander bus).

Each NIS module connects to its INFI-NET communication

loop by a cable connected to an NTCL01 Communication Ter

mination Unit or NICL01 Communication Termination Module.

Communication between nodes is through coax or twinax

cables that connect the termination units or modules on each

node. Power and I/O expander bus connections follow the

same connector assignments common to most INFI 90 OPEN

modules (P1 for power, P2 for I/O expander bus).

The INIIT12 INFI-NET to INFI-NET Transfer Module supports

bidirectional communication through two RS-232-C ports. Port

one passes system data only. Port two passes system data or

can be used as a diagnostic port. The central INIIT12 module

can use a variety of means to link to the satellite INIIT12 mod

ule such as modems, microwave and transceivers. The INIIT12

module communicates directly with an NIS module through

the I/O expander bus.

INIIT12 INFI-NET to INFI-NET Transfer Module

The NIS module works in conjunction with the INFI-NET to

INFI-NET transfer modules. This allows any node to communi

cate with any other node within the INFI-NET system.

The NIS module is a single printed circuit board that occupies

one slot in the module mounting unit (MMU). The circuit board

contains microprocessor based communication circuitry that

enables it to interface with the INFI-NET to INFI-NET transfer

modules via the I/O expander bus. Both the INFI-NET to

INFI-NET interfaces require a specific interface module and an

NIS module (the INIIL02 module requires two NIS modules).

Two captive latches on the front-mounted faceplate secure the

module to the MMU card cage. There are 16 LEDs on the face

plate that display error codes or event/error counts.

INTENDED USER

Anyone who installs, operates or performs maintenance on the

INFI-NET to INFI-NET interfaces should read this manual

before placing an interface into service. Installation requires an

engineer or technician with experience handling electronic cir

cuitry and who is familiar with communication networks.

INTERFACE DESCRIPTION

The INFI-NET to INFI-NET interfaces are the INIIR01 INFI-NET

to INFI-NET Remote Interface and the INIIL02 INFI-NET to

INFI-NET Local Interface. The INNIS01 Network Interface Slave

Module is the front end of the INFI-NET to INFI-NET interfaces.

It is the intelligent link between a node and the INFI-NET loop.

The network interface slave (NIS) module and an INFI-NET to

INFI-NET transfer module create a specific node interface.

The INIIR01 INFI-NET to INFI-NET Remote Interface is made

up of the NIS module and the INIIT12 INFI-NET to INFI-NET

Transfer Module. This interface is a node on a central loop that

can communicate to an interface node on a remote satellite

loop (two interfaces are required, refer to Figure 1-1). Bidirec

tional communication from the central loop to the remote sat

ellite loop is through standard RS-232-C ports. The INFI-NET

to INFI-NET remote interface can support hardware redun

dancy. Refer to Appendix E for information on hardware

redundancy.

INTRODUCTION

INFI-NET is a unidirectional, high speed serial data highway

shared by all INFI 90® OPEN nodes. The INFI-NET to INFI-NET

interface modules provide sophisticated interfaces for data

exchange between nodes on an INFI-NET communication net

work. These network interface units use state-of-the-art INFI

90 OPEN modules.

This interface transfers system data, control and configuration

messages, and exception reports between the central and

remote INFI-NET loops. Many of the operating characteristics

of the INIIT12 module are determined by specifications in the

INIIT12 executive block (function code 202). These specifica

tions are configurable to fit the needs of the application.

Prerequisites

— Good engineering knowledge of AC

drives and motors

— Personal computer knowledge

— Laptop with DriveDebug and Drive

Window loaded, fiber optic program

ming tool (RUSB-02)

— Successful completion of the e-learn

ing course (G711e)

— The participant will be enrolled auto

matically into the e-learning course

(G711e) by applying for the G711

course.

E-learning topics

Generalities

— ABB medium voltage drives family

overview

— Three-level inverter topology, DTC

control

— Options and typical applications

Control Hardware description

— Component and PCB functions

— Main circuit diagrams

— PCB settings and configuration

Hardware description

— Air cooled drive

— Water cooled drive

— ACS1000i drive

Protection concept

— Fault classes

— Protective reactions

Classroom topics

Generalities

— MV data base instruction

— Software compatibility and downloading sequence

Course goal

The goal of this course is to introduce the ACS1000 Variable Frequency Drive to the field ser

vice engineers and to teach them in a safe and instructive environment the techniques re

quired to carry out the correct procedure in commissioning, servicing and maintaining this drive.

Main learning objectives

Upon completion of this course, the par

ticipants will be able to: – Understand the drive system topology – Carry out basic commissioning, ser

vice and maintenance work as well as

fault-tracing – Verify and modify drive parameters – Locate and replace faulty hardware

components – Using MV Drive Portal database to up

date the knowledge of the drive, get

familiar with spare parts and warranty

issues handling – Start the certification program for

commissioning; after completion of

the certification program the partici

pants are allowed to commission the

medium voltage drive system

Participant profile

Commissioning, field service, testing and

maintenance personnel of ABB or certified

technical partners.

The concept of security zoning is described in IEC62443. In short,

security zoning is a method to segment a system into zones with

different security levels. A security level is complied with by

implementing a combination of security counter measures. The

reason why it potentialy could make sense to divide a system into

security zones, which comply with different security levels, could be

that the risk for different parts of the system varies. Another could be

that the impact of a potential incident varies.

NE870 supports RNRP (Redundant Network Routing Protocol), which

enables 800xA to have two physicaly separate networks, and thereby

avoid single point of failure.

Features and benefits

• NE870 has a redundant power supply and alarm function

• Wide operating voltage range (16 VDC to 60 VDC)

• Back end holds a casted DIN clip for stable mounting on a DIN-rail

• Digital IO for monitoring

• Console port for management using CLI

• USB port for easy save and load system configuration

• 3 x RJ-45 10/100/1000 Ethernet TX connectors

• 8 x RJ-45 10/100 Ethernet TX connectors

• Status LED‘s

1. Robust Construction & Durability
   • Material: Housed in a PP + 304 stainless steel composite shell, offering corrosion resistance and longevity.
   • IP Rating: IP54 protection ensures dust and splash resistance, ideal for industrial environments.
   • Compact Design: Dimensions of 560mm × 380mm × 820mm allow for space-efficient installation in standard racks.
2. Intelligent Monitoring & Control
   • 7-Inch Touchscreen Interface: Enables real-time monitoring of system status, manual/automatic mode switching, and data logging (≥1,000 records).
   • Modbus RS-485 Communication: Facilitates seamless integration with SCADA or other plant automation systems.
   • Diagnostic Alerts: Provides fault codes (e.g., E01 for low flow, E12 for regenerant shortage) and remote troubleshooting support.
3. Safety & Environmental Compliance
   • Leak Detection: Integrated leak sensors trigger audible/visual alarms to prevent water damage.
   • Overpressure Protection: A pressure relief valve (0.8 MPa) safeguards against system overpressure.
   • Eco-Friendly Regeneration: Waste neutralization ensures pH-compliant discharge (6.5–7.5) per ISO 14001 standards.

Applications

• Semiconductor Manufacturing: Critical for rinsing, etching, and chemical dilution processes.
• Pharmaceuticals: Ensures compliance with GMP standards for injectable water and dialysis solutions.
• Power Generation: Used in boiler feedwater treatment and turbine cooling systems.
• Laboratory Research: Supports analytical instrumentation and high-precision experiments.

Optional Enhancements

• UV Sterilization Module: Reduces total organic carbon (TOC) to <5 ppb for ultra-low-contamination applications.
• Activated Carbon Adsorption: Mitigates organic impurities in challenging feedwater sources.
• Multistage Systems: Configurable for parallel or serial operation with RO/EDI units to achieve flow rates up to 2,000 L/h.

Certifications & Standards

• Complies with ISO 9001, CE, and RoHS directives.
• Meets GMP and SEMI F72 guidelines for ultrapure water in semiconductor and pharmaceutical industries.

The ABB 3BHL001433P0001 Q-0730-A Deionizer is engineered for reliability, precision, and ease of use, making it a trusted solution for industries demanding the highest water purity standards.

ABB 3BHL001433P0001 Q-0730-A DEIONIZER Product Description

The ABB 3BHL001433P0001 Q-0730-A Deionizer is a high-performance, industrial-grade water purification system designed to deliver ultrapure water for critical applications in semiconductor manufacturing, pharmaceuticals, power generation, and laboratory research. This deionizer combines advanced ion exchange technology with intelligent control systems to ensure consistent water quality and operational efficiency.

Key Features & Specifications

1. High-Capacity Ion Exchange Performance
   • Flow Rate: Up to 730 liters per hour (L/h) for continuous, high-volume deionization.
   • Water Quality: Produces water with a resistivity of ≥18 MΩ·cm (at 25°C), meeting stringent ultrapure water standards.
   • Operating Pressure: Supports a pressure range of 0.2–0.6 MPa, ensuring compatibility with diverse industrial systems.
   • Temperature Tolerance: Operates efficiently in water temperatures ranging from 5°C to 45°C.
2. Advanced Ion Exchange Resin Technology
   • Mixed-Bed Resin Configuration: Utilizes a dual-layer cation/anion resin bed for optimal ion removal efficiency.
   • Regeneration System: Equipped with a dual-channel regenerant (HCl/NaOH) injection system, minimizing chemical consumption and waste.
   • Smart Regeneration Control: An integrated conductivity monitor triggers automatic resin regeneration when water quality drops below a user-set threshold (1–15 MΩ·cm).