The IC200ALG630 has a backplane current consumption of 3 mA at the 125 VDC and 5.3 VDC outputs on the backplane.

It is also rated for optical and frame-to-ground isolation with a continuous voltage duration of 250 VAC and a 1500 VAC voltage duration of 1 minute.

The module also provides LED status indicators, specifically an OK LED that indicates active backplane power when the module fails, and amber when lit green.

The IC200ALG630 module is GE’s 16-bit analog input module. It is an industrial module designed to handle a wide range of application requirements.

It comes with a 7-bit thermocouple with 16 channels. This thermocouple analog input module receives power from the backplane power supply.

It offers four cold end compensation options, no cold end, remote cold end, fixed cold end, and localized cold end compensation.

It is rated at 5 volts DC. It supports different thermocouples of type J, K, T, S and R.

The IC200ALG630 module is capable of drawing a total of 5 milliamps of current from the 125 volt bus.

The update rate of the analog module is 60 milliseconds for 60 Hz and 50 milliseconds for 70 Hz.

An OK indicator on the front of the module indicates the presence of backplane power.

The IC200ALG630 module has a compact design that saves panel space.

It measures 4.3 inches wide, 2.63 inches high, and 1.95 inches deep.

The temperature range should be set between 0 and 60 degrees Celsius. The thermocouple module has advanced diagnostic features.

It can issue channel-specific alarm reports. It can also detect over- and under-range conditions in the input.

Faults caused by thermistors can be easily detected by the module as internal faults. The module has not experienced thermal derating.

About the IC670GBI001

The IC670GBI001 bus interface is a GE Fanuc component for field control devices.

GE Fanuc is a well-known producer of technology solutions for many industries, and the GE IC670GBI001 Bus Interface module is resistant to noise in industrial environments,

vibration, high and low temperatures, humidity, and other common conditions in industrial environments.The IC670GBI001 bus interface unit has a nominal voltage rating of 115 volts AC and 125 volts DC.

The input frequency range is 47 to 63 Hz. The unit’s voltage range is 90 to 135 volts AC and 105 to 150 volts DC.

The IC670GBI001 Bus Interface Module has a rated power consumption rating of 115 volt-amperes (**value) at 48 volts AC at full load.

The power consumption rating at 24 volts AC at full load is 125 watts (**value). The unit has a hold-up time of 20 milliseconds and a power supply output voltage of 6.5 volts DC.

The IC670GBI002 Bus Interface Module works well with other components such as the Bus Interface Unit power supply and Bus Interface Unit terminal blocks.

The IC670GBI001 module has a high-quality housing made of aluminum and includes LED indicators for status updates as well as an HHM connector for handheld displays.

The IC670GBI001 bus interface unit has a logic power supply and its configuration file is stored in the memory of the terminal block.

The four included indicators are the “PWR”, “OK”, “Run” and “Bus B” LEDs. The LEDs indicate the normal operation of the module and the communication status with the CPU.

Since the IC670GBI002 unit can be used with a DC power supply, the backplane current may be limited by the lower input voltage.

The module is also compatible with Ethernet, Genius, Profibus, and DeviceNet firmware. It is also compatible with PLC CPU firmware and VersaPro software.

The GE Fanuc Automation IC200ALG328 Versamax I/O module has a thermal derating only when used at 30 volts DC and placed in a specific location on the DIN rail.

This derating is also dependent on the ambient air temperature present.GE Fanuc Automation IC200ALG328 Versamax I/O Modules are rated for 18 to 30 volts DC.

The current draw is rated at 2 amps inrush current, and the power consumption is rated at 100 milliamps without load and 12 milliamps at full scale using all 270 outputs.

The module has a 13-bit resolution with an accuracy rating of up to 1%. The module is equipped with 2 LEDs and a diagnostic tool.

It can be hot-plugged, but this needs to be done carefully to retain all components in the rack and module.

The IC200ALG328 is a 12-channel, 13-bit current analog output module designed for the GE Fanuc Versamax family.

The IC200ALG328 has a default output range, but the output range can be easily changed with jumpers.

All outputs require external power, and the IC200ALG328 module will be intelligently processed by the CPU or Network Interface Unit.

If the backplane power or communication is interrupted, or if the PLC stops running, the outputs of the IC200ALG328 module can be easily kept in their last state, or in their default state via jumpers.

The backplane must send different output data to the module or the outputs will remain in their default or previous state.

In 0-20mA range mode, the current output signal value of 0mA corresponds to a %AQ value of 0 count and 20mA corresponds to a %AQ value of +32.000 count.

If in 4-20mA range mode, 0 %AQ count value corresponds to 4mA output current and +32.000 %AQ count value corresponds to 20mA output current.

If the IC200ALG328 is placed in the PLC rack, the negative value will be adapted and commanded as 0mA regardless of the range selected.