Category: GE

The Full Current Output Option Relay 139-H-FLC is a horizontal mounting specialty model.

This model has an external reset switch that works in conjunction with the front panel reset switch.

This model also has an emergency restart option.

Product Description

Model 139-H-FLC is a full load current horizontal mount motor protection relay.

This model has a full load current of 4 to 20 milliamps. Associated protections listed for this relay include overheating, stall-mechanical blocking,

Rotor Lockout, Undercurrent, Ground Fault, Single Phase/Unbalance, Repeat Start, and Overload Protection with selectable curves.

This relay will protect three-phase AC motors from environmental influences that can cause damage.

The 139-H-FLC relay will be used in six applications; one of the applications is to ensure user safety.

This application will utilize the ground fault function to find leakage currents caused by moisture or potential winding shorts in mines, thus preventing shock hazards.

As mentioned above, the relay will be mounted horizontally; it should be noted that a rectangular panel cutout is required for whichever mounting orientation is chosen for the relay.

Once the current breaker is available, the relay will be held in place by two U-clips and then prepared for wiring.

The 139-H-FLC relay can be supplied with ground fault current and it will accept all current carrying conductors through the ground fault current window.

Please note that it is highly recommended that at least two current leads need to be wound together to minimize noise pickup on the relay.

There is a specially designed current that can be used to help output lower level signals.

Product Description

General Electric designed the 531X307LTBAJG1 as a local area network (LAN) termination board.

It is located under the 531X Series Replacement Board.GE Series drives and exciters can have this card installed in their enclosures.

With this card installed, there will be an interface system between the external devices and the control drive.

Peripheral devices such as interlocks, pushbuttons, and indicators can use the card as an interface.

When the 531X307LTBAJG1 board is installed, the LAN signals are distributed through the interface platform.

When the board is installed, eight configurable control input plugs are available for the drive.

The board accepts input voltages rated from 2 to 240 V, both AC and DC.

The input voltage sent to the control board is converted to a 24 VDC logic signal acceptable to the control board.

The signals generated by the control board can be easily transmitted through the LAN terminals, the drive control board, and the NTB terminal board.

The seven integrated control outputs of the control board consist of low-current and low-voltage C-type relay contact connectors.

The user should observe the installation parameters provided by the device manufacturer. These guidelines may prevent some damage to the equipment.

Only trained personnel qualified to install the board should be allowed to operate the 531X307LTBAJG1 LAN terminal.

Detailed instructions on wiring procedures can be found in the board’s data sheet and manual.

As with all other members of the 531X family, technical support for this card is initially provided by the manufacturer, General Electric.

Product Description.

This DS200ADPBG1ABB Genius Adapter Board is a circuit board product from General Electric.

In addition to its functional description as a Genius Adapter Board and a Mark V series turbine control system originally attributed to General Electric, there is some mystery surrounding this product.

There is a bit of mystery surrounding this product. While it could be loosely defined as a General Electric product.

Although loosely defined as a General Electric product, it is likely that this Mark V series product was originally manufactured by a subsidiary of General Electric, such as General Electric Transmission Systems, Inc.

such as GE Drive Systems or GE Industrial Control Systems.

Before deciding to purchase a DS200ADPBG1ABB Mark V Genius Adapter Board.

Consider that this product has used all three of its possible major product revisions, which may have significantly changed its originally labelled performance specifications and dimensions.

Hardware tips and specifications

As with any Mark V Series product, the DS200ADPBG1ABB Genius Adapter Board uses a unique set of advanced hardware components and component specifications

to achieve its intended functionality. First, the Genius I/O Adapter Board DS200ADPBG1ABB features a configuration board consisting of eight switches.

The Genius I/O Adapter Board DS200ADPBG1ABB is also equipped with a 40-pin connector and a 26-pin connector.

The third and final intuitively recognisable hardware element is critical to the DS200ADPBG1ABB Genius Adapter Board.

That is its array of manually removable hardware jumpers, which are included in its assembly for the highest customisation purposes.

The information stored on this personalised DS200ADPBG1ABB product page is the extent of the information that can be retrieved when checking the available DS200ADPBG1ABB manual data.

Nevertheless, a great deal of information can still be retrieved from the DS200ADPBG1ABB product number itself (beginning with the DS200 series label).

The series label has a double naming responsibility for this Mark V series product, indicating that it is a domestically produced General Electric product with a normal type of assembly.

About the IC695CPE305

The IC695CPE305 programmable automation controller (PAC) is part of the PACSystems RX3i automation platform.

The controller was manufactured by then GE Fanuc Automation (now Emerson Automation).

The IC695CPE305 has advanced features that are superior to most of today’s PACs.

The controller has the capability of Ethernet communication via one (1) Ethernet communication port.

The port supports 10/100 Mbps communication rates and can be used to communicate with programming workstations, Human Machine Interfaces (HMIs), Supervisory Control and Data Acquisition (SCADA) systems.

third-party hardware and software products, and controllers on the same platform for messaging and inter-controller data exchange.

In addition, the Ethernet port supports OPC UA, allowing connection to third-party devices via the OPC protocol.

The IC695CPE305 is not limited to Ethernet communication as the controller also integrates two (2) serial ports that support RS232 and RS485 communication standards.

It is also equipped with one (1) USB 2.0 master port that allows downloading and uploading of user programmes from a smartphone’s thumb drive.

The IC695CPE305 5MB RAM and 5MB non-volatile user memory has a processor speed of 1.1 GHz and a typical scan rate of 0.72 milliseconds per 1.000 Boolean instructions.

It supports a variety of network protocols such as Ethernet (PROFINET, Ethernet Global Data, Channel, Modbus TCP server and client),

Genius, PROFIBUS DP, and DeviceNet.The IC695CPE305 allows control of up to eight (8) racks, including CPU racks.

This controller supports the installation of additional communication cards that support Serial, Genius, CMX (Reflective Memory), and Ethernet.

This single-slot controller supports up to eight local racks.

The IC670MDL644 24-volt DC positive/negative input module has a parallel-to-serial converter.

This converts the data in the data buffer to a serial format that can be used with the Bus Interface Module.

When the Bus Interface Module is properly connected, the module’s power LED indicates the power status.

The Bus Interface Module starts reading the processed and converted input data.

The Bus Interface Module has both positive and negative inputs. The positive input is used in order to receive the current from the input device.

The negative input is used to supply current to the input device.

Efficient field wiring of the IC670MDL644 input module can be performed using a terminal block with box terminals or isolated terminals.

The internal circuitry of the module is equipped with a network of resistors and capacitors to provide input thresholding and filtering.

The IC670MDL644 24-volt DC positive/negative input module is a field control logic fast input module manufactured by GE Fanuc.

It provides a set of discrete inputs that can be driven by both positive and negative logic.

The IC670MDL644 24-volt DC positive/negative input module has 16 inputs,

separate LEDs for logic-side inputs and a “PWR” indication LED for monitoring power status.

The bus interface unit provides the power needed to drive the 5-volt logic, and the input devices require power from an external 24-volt DC power supply.

It also provides isolation ratings such as 250 volt AC continuous user input to logic isolation and 1500 volt AC user input to frame ground isolation for 1 minute.

Functionality

The bus controller can exchange up to 128 bytes with each device on the Genius I/O bus.

Genius blocks and other devices on the bus automatically report faults, alarms, and certain other predefined conditions to the Bus Controller.

The bus controller stores any diagnostic information it receives, which is automatically read by the CPU. The CPU reads this information automatically. The faults can then be displayed in a fault table using programmed software.

The bus controller supports all Genius datagrams.

The bus controller can send up to 128 bytes of global data per bus scan.

Global data is data that is automatically and repeatedly broadcast by the Genius Bus Controller.

A bus controller can receive up to 128 bytes of global data per bus scan from other bus controllers on its bus.

An RX3i system can contain up to eight Genius Bus Controllers.

LED Indicators

The LEDs on the front of the Genius Bus Controller indicate its operational status. Both LEDs should be lit during normal operation.

OK displays the status of the bus controller. This LED is illuminated when power-up diagnostics are complete.

COM shows the status of the Genius communications bus. This LED is always on when the bus is operating normally.

It blinks during intermittent bus errors and goes out during bus failures. This LED is also off when no configuration is received from the CPU.

The IC694BEM331 supports transmission rates of 153.5Kbaud standard/extended, 76.8Kbaud, or 38.4Kbaud, which are configurable through software.

The required bus termination resistors at each end of the bus cable are 75. 100. 120. or 150 ohms.

The GE controllers have an isolation rating of 2000 volts and a transient common mode rejection isolation rating of 1500 volts.

The GE Fanuc EX3i PacSystems IC694BEM331 bus controller is configured using Proficy Machine Edition software.

It is rated at 300 mA. The bus controller is rated at 5 volts DC.

The bus controller has advanced diagnostic capabilities to accurately locate faults and errors in the operation of the PLC system.

The controller communicates using global data and datagrams.The IC694BEM331 Bus Controller is compact and can be easily installed into a complete PLC system.

The IC694BEM331 bus controller uses daisy-chained or twisted-pair cable. The controller is compatible with GE 90-30 series and 6 series PLC systems.

Product Description

The IC693CHS397 is a 5-slot expansion baseboard for the 90-30 Series Programmable Logic Controller (PLC) platform.

Formerly manufactured by GE Fanuc and now part of Emerson Automation, this baseboard has five (5) main I/O slots,

one (1) power slot, and one (1) expansion port. The module supports the installation of standard 90-30 series I/O modules and specialized modules.

It can be mounted directly to the panel using the supplied mounting tabs.

About the IC693CHS398

The IC693CHS398 is an expansion backplane for the 90-30 Series PLCs, formerly manufactured by GE Fanuc and now part of Emerson Automation.

The module can be paired with a CPU baseboard and connected through the expansion port on the CPU baseboard.

With the IC693CHS398. the central processing unit (CPU) module can control additional I/O modules.

The number of expansion boards (e.g., IC693CHS398) allowed per system varies depending on the type of CPU used.

Specifically, up to four expansion boards can be used simultaneously for any of the CPUs 331. 340. and 341. and up to four expansion boards can be used simultaneously for CPU 350 and above.

The IC693CHS398 is equipped with five (5) I/O slots for option modules.

These slots are uniquely sized to prevent improper module installation. This backplane requires a dedicated power supply module to operate.

The power supply is installed through a dedicated power supply slot located on the left side of the hardware. There is also an expansion baseboard port on the far right side of the hardware for connecting additional expansion baseboards.

Product Description

The VMIVME-3122 is a member of VMIC’s extensive VMEbus analog I/O product line.

It features 16-bit digital resolution, program-controlled gain, selectable slew rates, and auto-scanning for 64 differential or single-ended channels,

Auto-scan for 64 differential or single-ended analog inputs.

The VMIVME-3122 has excellent dynamic range and analog input channel density. Multiple modes of operation are supported, including auto-scan, data burst, and external synchronization.

The board interfaces directly with VMIC’s family of signal conditioning boards to digitize the outputs of thermocouples, RTDs, and strain gages.

Individual channel gains can be downloaded for use during scanning operations, or the board can be configured for fixed gains. The boards can be configured for fixed gain common to all channels.

Multiple boards can be synchronized together, allowing up to 16 boards to start each scan simultaneously.

Interval timers, bus interrupters, channel counters, and mid-scan/end-of-scan flags simplify monitoring of data in the dual-port data buffer.

System applications that can benefit from the features of the VMIVME-3122 include factory automation, process control, data acquisition systems, training simulators, and laboratory instrumentation

The following overview of key features illustrates the flexibility and performance of the VMIVME-3122:

– 16. 32. or 64 differential or single-ended analog inputs

– 16-bit A/D conversion

– Selectable sweep rates from 381 Hz to 100 kHz (high performance option), 381 Hz to 50 kHz (standard performance option)

– Programmable gain of x1 or x10

– A/D converter ranges of ±2.5 V, ±5 V, ±10 V, 0 to +5 V, 0 to +10 V

– Programmable channel gain

– 16- to 1.024-word dual-port data buffer

– Operates in short I/O (A16), standard (A24), or extended (A32) data spaces

– Programmable channel block size and buffer size

– Optional low-pass input filter

– Continuous and burst operation modes

– Free-run or external/internal trigger

– Bus interrupter for mid-scan or end-scan indication

– Programmable interval timer for timing data bursts

– Direct wiring from VMIC signal conditioning boards

– Initialized after reset in Auto Scan mode, gain = x1

Functional Features

– High-speed, easy-to-use fiber optic network (serial rate of 2.12 Gbaud)

– Data written to the memory of one node is also written to the memory of all nodes on the network

– Up to 256 nodes

– Connections up to 300 meters to multimode fiber and up to 10 kilometers to single-mode fiber

– Dynamic packet size, 4 to 64 bytes of data

– Transfer rates 47.1MB/sec (4-byte packets) to 174MB/sec (64-byte packets)

– 64MB or 128MB SDRAM Reflective memory

– Two independent DMA channels

– Any node on the network can generate an interrupt in any other node on the network or in all network nodes with a single command

– Error Detection

– Redundant transfer mode for additional error suppression

– No processor overhead

– Processor is not involved in network operation

– PCI 64-bit 66MHz Transport

– Compliant with PCI Revision 2.2

– Includes VMISFT-RFM2g network and shared memory drivers.

Features

Description: The VMIPCI-5565 is the PCI member of the VMIxxx-5565 family of reflective memory (RFM) real-time networking products from GE Fanuc Embedded Systems.

Other members of this family include the VME-compatible board VMIVME-5565 and the PCI mezzanine card (PMC) VMIPMC-5565.

All three products are network compatible and can be integrated into a network in any combination.

This family of products allows computers, workstations, programmable logic controllers (PLCs) and other embedded controllers with different operating systems or no operating system at all to share data in real time.

Functional Features

– 128-bit voltage output

– High current driver (350 mA current source)

– Heavy duty options available

– Automatic overcurrent shutdown protection

– Thermal shutdown protection

– Output fault indication provided in status register

– High breakdown voltage (35 V)

– Output clamp diode for inductive flyback protection

– Compatible with intelligent I/O controllers

– Built-in test logic for fault isolation

– Compatible with VME bus (ANSI/IEEE STD 1014-1987 IEC 821 and 297)

– A24:A16:D32/D16/D08 (EO): Slave 39/3D:29/2D:6U Form Factor

– Front Panel with Fault LED

– Preheat resistor sockets available, to be supplied by the user

– External power supply can be connected on the front panel (P3 to P4) or on P2.

Compliance: This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987 IEC 821 and 297) and uses the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave: 39/3D:29/2D:6U form factor

Output Connector Types: Three types of female mating connectors are available for use with the P3 and P4 interfaces: 96-pin mass termination (IDC) connectors, 64-pin IDC connectors, and 96-pin discrete wire connectors.

Part numbers for ERNI IDC DIN 96-pin and 0.033-inch 30 AWG ribbon cable are

96-pin connector 913 031 (ERNI)

96-pin cable 913 049 (ERNI)

Part numbers for Panduit IDC DIN 64-pin connectors and 0.050-inch ribbon cable are

64-pin connector 120-964-435E (Panduit)

Strain Relief 100-000-032 (Panduit)

64-conductor cable 9V28064-XXX (Belden)

Harting discrete wire connectors consist of a contact housing with female crimp contacts.

Housing with female crimp contacts Harting part numbers are as follows

96-pin connector 09 03 096 3214 (Harting)

Female crimp 09 02 000 8484 (Harting)