Welcome to the official website of CNIACS Automation Technology Co., Ltd!
0
April 14, 2025 BY
IN GE

IC660BBD022 16 Circuit Enabled Source I/O Module

The IC660BBD022 is a Genius protocol-enabled module that is part of the Genius I/O Block series of distributed I/O modules. The device is a stand-alone, single node I/O station with sixteen (16) I/O circuits that supports source-wired configurations.

The IC660BBD022 has sixteen (16) I/O circuits and operates at 24 / 48 VDC.Each channel of the module can be configured as an input and an output, and is capable of exchanging data over the supplied Genius I/O Bus Terminal, allowing the module to be used in a wide variety of applications including GE Programmable Logic and Automation Controllers (PLC / PAC) as well as Bus Controllers, PC Interface Modules, Human Machine Interfaces (HMI) and third party devices.

The module is a panel-mounted, self-contained device in an open enclosure, so it must be mounted inside the enclosure to provide adequate protection from industrial contaminants.

The module can be mounted remotely with a maximum distance of 7.500 feet from partner equipment. It also allows daisy-chaining of other I/O modules www.cniacs.com to form a Genius I/O network. Operation of the module can be configured locally using a handheld monitor (HHM) through the HHM port mounted on top of the terminal assembly.

It can also be configured remotely using the host controller’s programming software. The module’s input channels accept 12 / 24 VDC nominal voltage with a 1.7 ms start-up delay. Similarly, the output channels generate 2 amps of current per circuit with a maximum turn-on delay of 1 ms. The module consists of two (2) assemblies, specifically the IC660EBD020 electronics assembly and the IC660TBD022 terminal base assembly.

The IC660BBD022 I/O module is a 16 circuit enabled source I/O module manufactured by GE Fanuc. It uses a 24-volt DC power supply and can be used with both 2-wire and 3-wire sensors.The Genius I/O device has a load current of 2 amps, and this DC power block has intelligence that makes it easy to configure as a sensor or actuator device. It also has other configurable features including output power defaults, selectable input filtering time, and an output pulse test function.

The IC660BBD022 I/O module has diagnostic features and safety measures that easily alert operators to runtime and operational errors. It easily detects errors such as overload, overheat, short-circuit, no-load, and switch faults. The unit is portable and compact. It saves panel space and measures 8.83 inches high, 4.42 inches deep and 3.56 inches wide.
April 14, 2025 BY
IN GE

Fanuc IC698CHS109 Racks I/O Racks for Rx7i PACsystems

Description: The GE Fanuc IC698CHS109 rack is an I/O rack for the Rx7i PACsystem.

This 8-slot I/O rack is software configurable and supports all Rx7i CPU and I/O configurations for VME64 backplane systems,

90-70 series I/O devices and VME modules.

The GE Fanuc IC698CHS109 Rx7i Rack is a front-mounted I/O rack designed for the Rx7i PACsystem family.

The Rx7i PACsystem chassis uses the VME64 base system, which is four times faster than existing VME systems, providing faster I/O throughput.

It supports RX9i CPUs and VME modules (including 90-70 series I/O) as well as VMIC modules.

The IC698CHS109 Rack features automatic daisy-chained interrupt profiles and Bus Grant (BG) signals, eliminating the need for slot jumpers.

The IC698CHS109 Rack also features a backplane connector (J2 connector) that provides high-speed VME data transfer of up to 64 bits per cycle.

It also accepts plug-in Rx7i power supplies. The rack’s I/O addressing is software configurable through the Machine Edition Logic Developer-PLC software.

No DIP switches or jumpers are required www.cniacs.com on the connected I/O modules.

The GE Fanuc IC698CHS109 rack requires 350 watts of power to operate. It is rated for 60 watts of current at 5 volts DC and 12 volts DC, respectively.

The IC698CHS109 chassis has nine I/O slots (labelled 1 through 9) for mounting CPUs, I/O modules, and other devices.

The IC698CHS109 chassis has nine I/O slots (labelled 1 through 9) for the CPU, I/O modules, and power supply modules.

I/O slots 1 through 8 all have a slot width of 20.3 mm, slot 9 has a slot width of 40.5 mm, and the power supply module slot (also referred to as slot 0) has a slot width of 61 mm.

The I/O modules in the IC698CHS109 chassis can be arranged in a configuration of seven single-wide modules, four double-wide modules, or a mix of single and double-wide modules.

The IC698CHS109 chassis supports IP 54 or higher rated mounting enclosures with an operating temperature range of 0 to 60 degrees Celsius.
April 14, 2025 BY
IN GE

Fanuc IC693BEM320 Solid State Serial I/O Interface Module

Description: The GE Fanuc IC693BEM320 I/O Link Module is a serial interface device.

It can connect up to 64 I/O points in a GE Fanuc 90-30 or 90-70 series programmable logic controller (PLC).

It has 2 serial ports and supports RS-485 and RS-422 connections.

GE Fanuc designs and manufactures a solid-state serial interface module called the IC693BEM320 Solid-State Serial I/O Interface Module.

The module is used to interconnect the proprietary GE Fanuc I/O Link networking protocol to a Series 90-30 or Series 90-70 Programmable Logic Controller (PLC).

The module can be configured to transfer 32 or 64 I/O points to GE Fanuc I/O Link.

The GE Fanuc IC693BEM320 I/O module can be configured to transfer 32 or 64 I/O points to GE Fanuc I/O Link, but only as a slave module, not as a master module.

Simply set the jumpers located inside the front cover to the correct mode, depending on the user’s application.

The module has two serial communication ports, one for RS-485 serial protocol and the other for RS-422 serial protocol.

The GE Fanuc IC693BEM320 I/O Interface Module should always be operated within a temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).

Humidity range is 5 to 95% (non-condensing). If more extreme environmental conditions are expected, it is

It is strongly recommended that a climate control system be used on the panel where the GE Fanuc PLC and modules are installed.

Module installation should be done by www.cniacs.com a qualified technician by sliding the GE Fanuc IC693BEM320 I/O Interface Module into the

Slide the GE Fanuc IC693BEM320 I/O Interface Module into any available slot on the 90-30 or 90-70 series PLC backplane. There are two status LEDs on the front of the module.

One indicates if the module is properly powered on and the other indicates if the module is functioning properly.

Up to 16 GE Fanuc IC693BEM320 I/O Interface Modules can be set up as slaves to the master PLC.
April 14, 2025 BY
IN A-B

A-B 6176M-19PN VersaView Standard Industrial Monitor

Product Description The 6176M-19PN monitor is a VersaView Series industrial monitor.

designed and manufactured by Allen-Bradley/Rockwell Automation.

It can be used to control and display data from Allen-Bradley VersaView series non-monitor computers.

The 6176M-19PN monitor has a 19-inch wide screen with colour graphics.

The monitor operates in temperatures from 32 to 104 degrees Fahrenheit and is housed in an IP 66 rated enclosure.

The Allen-Bradley 6176M-19PN is a VersaView standard industrial monitor.

It has a 19-inch screen with a native resolution of 1280 x 1024 pixels and a contrast ratio of 800:1.

The flat panel display features a colour www.cniacs.com active matrix thin-film transistor screen with 16.7 million colours and a typical brightness of 250 cd/lux.

Typical brightness is 250 cd/m2 (nits). The backlight consists of CCFT lamps. Please note that this monitor requires external inputs, specifically a keyboard and mouse.

The 6176M-19PN monitor is mounted on a panel with an aluminium bezel and can be panel or rack mounted.

The monitor has one VGA and one DVI input with automatic selection.

Its rear control buttons are used to set the colour balance, contrast, brightness, video information, image lock, automatic on-screen setting (on-screen display or OSD),

The 6176M-19PN also has USB and RS-232 communication ports.

It has VGA and DVI video signals, and on-screen display (OSD) controls that provide image rotation, screen brightness, and contrast settings.

The monitor has an input voltage of 90-264V AC and a line frequency of 47-63 Hz.

The 6176M-19PN has a power consumption of 3.5 A and a power rating of 42 W. It has an operating temperature range of 32-104 oF.

It has an operating temperature range of 32-104 oF and is rated IP66 and NEMA Type 1/12/4 to protect against water and solid particle debris.
April 14, 2025 BY
IN A-B

A-B 6155R-NPXPDC Compact industrial computer without display

Description:

The 6155R-NPXPDC computer is an Allen-Bradley industrial computer without a display.

It is a Computer 6155R series computer.The 6155R-NPXPDC computer weighs 11 lbs.

The Allen-Bradley 6155R-NPXPDC computer is a compact industrial computer without a display.

The unit weighs approximately 11 lbs.

The dimensions of the computer (excluding handle and connectors) are 115 x 172 x 158 mm.

The 6155R-NPXPDC computer requires a DC power supply with 9 to 36 volts DC input.

The unit is rated at 35 watts and has a current rating of 3.89 amps at 9 volts DC.

The current rating is 0.97 amps at 36 volts DC.

Environmental specifications for the 6155R-NPXPDC computer include an operating temperature range of 32 to 131 degrees Fahrenheit,

Non-operating temperature range of 32 to 131 degrees Fahrenheit, non-operating temperature range of 4 to 140 degrees Fahrenheit, and non-condensing relative humidity range of 10 to 90%,

15-gram operating shock rating and 30-gram www.cniacs.com non-operating shock rating.

The 6155R-NPXPDC computer is an enhanced E-Series computer.

The 6155R-NPXPDC computer requires an external monitor.

The processor in this unit is an Intel Celeron M processor rated at 1 Gigahertz.

The 6155R-NPXPDC computer has 2 GB of available memory and the maximum memory supported by the system is also 2 GB.

The 6155R-NPXPDC computer supports 2 CompactFlash Type II card slots.

The I/O ports available on the device include 2 serial ports, 1 PS/2 keyboard port, and 1 PS/2 mouse port,

4 USB 2.0 ports, 1 VGA port, and 1 audio line out port.

The 6155R-NPXPDC computer supports two 10/100/1000 Mbps Ethernet LAN ports.

The 6155R-NPXPDC computer is designed for use in industrial or control room environments that are isolated from the main AC power supply.
April 11, 2025 BY
IN A-B

A-B 6177R-MMPW7 Rackmount PC VersaView Series

Product Description

The 6177R-MMPW7 computer is an Allen-Bradley/Rockwell Automation VersaView series non-display computer.

It can be equipped with an Allen-Bradley/Rockwell Automation VersaView monitor if the application requires a display.

The 6177R-MMPW7 non-display computer has 4 GB of www.cniacs.com memory and 500 GB of hard drive storage.

It operates on a voltage range of 100 to 240 VAC and a frequency of 50 to 60 Hz.

The 6177R-MMPW7 non-monitor computer has an operating temperature of 0 to 50 degrees Celsius and a storage temperature of -20 to 60 degrees Celsius.

The Allen-Bradley 6177R-MMPW7 is a machine-mountable, high-performance VersaView 750R non-display industrial computer.

This AC-powered computer uses an Intel Core i3-2120 3.3 GHz processor with 4 GB of DDR3 memory, expandable up to 32 GB.

Note that the 3.5-inch hard drive installed in this computer has 500 GB of memory and uses a SATA interface.

The 6177R-MMPW7 PC is also equipped with a DVD-RW disc drive and four expansion slots.

There is one PCI, one PCI Express x16. one PCI Express x4 and one PCI Express x1 slot.

The I/O ports are 7 USB 2.0 ports (4 rear, 2 front, 1 internal), 1 front and 1 rear USB 3.0 port,

1 parallel port, 2 serial ports, 1 rear eSATAp, 2 PS2 ports, 1 microphone jack, and line-in/line-out jacks.

It also has 2 Ethernet 10/100/1000 LAN ports and 1 DVI-I and 1 DVI-D video ports with VGA support.

A VGA adapter is included with the computer.

The 6177R-MMPW7 is a cabinet computer that measures approximately 14.17 x 6.69 x 15.01 inches and weighs 30.36 pounds.

The 6177R-MMPW7 computer has an auto-range input voltage of 100-240 volts AC and draws 10 amps at 100 volts RMS and 10 amps at 240 volts RMS.

It draws 10 amps at 100 volts RMS and 5 amps at 240 volts RMS and has a line frequency of 50-60 Hz. Operating temperature is 0-50 °C, non-operating temperature is -20-60 °C.

Operating shock is 15 g and non-operating shock is 30 g at ½ sine 11 ms.

VersaView non-display series terminals are equipped with 4GB of DDR3 memory, 1 x 500 GB of storage and 100-240V AC input power.
April 11, 2025 BY
IN A-B

A-B 6181P-00N2HW71AC Non-Display Computer

Product Description.

The 6181P-00N2HW71AC computer is a non-display computer in the Allen-Bradley VersaView family.

It does not have a built-in display like the display computers.The 6181P-00N2HW71AC non-display computer has 100 GB of internal memory and 4 GB of RAM.

If you need to display data, you can connect an external monitor.

The 6181P-00N2HW71AC non-display computer operates on 100 to 240 volts AC.

The 6181P-00N2HW71AC is an Allen-Bradley non-display input terminal. It is a 100GB mountable terminal.

It has one RAM and one flash memory unit. The power range of the machine is 9.88 x 13.89 x 3.96 inches.

It is part of the VersaView NDM terminal www.cniacs.com product family. It also has an Intel i3-4102E processor.

It has 4GB of RAM, which allows this machine to operate quickly. It also makes the operator’s job easy.

Its input power supply is 120-240 volts AC. It can be mounted on a wall, table, shelf or machine.

The 6181P-00N2HW71AC has a 100GB memory capacity, which allows users to store information and save data for future reference and use.

The 6181P-00N2HW71AC is a non-display model that can be used for control, maintenance and basic information applications.

It has two serial ports. It also has one parallel port and two Ethernet ports, which are particularly suitable for operator communication.

It can be integrated into a computer for displaying operations in industrial environments.

It is easy to use and the operator can use it while controlling a machine in an industrial environment.

The device is equipped with an alphanumeric keypad and a small keypad with function keys that help the operator to easily connect to the machine.

It is located in the CD accessory of the module. The unit’s status hardware provides the user with an economical solution when the surrounding environment is harsh.

The VersaView non-display series terminals are equipped with 4 GB of RAM and 100 GB of storage and have an input power supply of 120-240V AC.
April 11, 2025 BY
IN A-B

A-B 6186M-15PTSS Industrial Performance Monitor

Product Description.

The Allen-Bradley 6186M-15PTSS is an industrial performance monitor: The Allen-Bradley 6186M-15PTSS is an industrial performance monitor.

It features a 15-inch colour active matrix TFT LCD with a native resolution of 1024 x 768 pixels.

It has a resistive touch input interface with a stainless steel bezel. It is powered by an external AC power supply with a voltage range of 100-240 VAC, 47-63 Hz.

It has RGB analogue video input signals and HD-15 VGA and DVI video input connectors.

The 6186M-15PTSS is an industrial performance monitor manufactured by Allen-Bradley.

The monitor can be used with commercially available computers and third-party industrial computers. For Allen-Bradley products.

It is especially compatible with VersaView and industrial non-monitor computers. The monitor has a video input port to provide visualisation.

The 6186M-15PTSS features a 15-inch screen with a native resolution of 1024×768. but optional frequencies and refresh rates are available.

such as 720 x 400 @ 70 Hz; 640 x 480 @ 60 Hz, 75 Hz; 800 x 600 @ 60 Hz, 75 Hz.

1024 x 768 @ 60 Hz, 70 Hz, 75 Hz; 1280 x 1024 @ 60 Hz, 75 Hz, with a response time of less than 35 ms.

The display features resistive touch screen inputs, backlighting and a half-life of 50.000 hours at 25 °C or 77 °F.

The 6186M-15PTSS has an RGB analogue video signal input and provides HD-15 VGA for analogue video signals and DVI for digital video signals.

The 6186M-15PTSS has RGB analogue video signal inputs and provides connectors such as HD-15 VGA for analogue video signals and DVI port for digital video signals. It also has a USB port.

It also has USB interfaces including one (1) Type B USB port for connection to a host computer and two (2) Type A USB 2.0 ports.

Electrical specifications for this industrial monitor include 100-240VAC power requirements and auto switching, line frequency of 47-63 Hz, and power consumption of 34W.

The 6186M-15PTSS industrial performance monitor is housed in a NEMA UL 50 1. 4. 4X, 12. and IP66 rated enclosure.

Required operating temperature is 0…. .55 °C (32…131 °F). .131 °F) and operating shock and vibration of 2 g peak, 10…640 Hz, and 20 g peak, respectively. .640 Hz and 20 g (1/2 sine wave, 11 ms).

The 6186M-15PTSS has two video input connectors www.cniacs.com on the back of the unit, a High Definition 15-pin Video Graphics Array (HD-15 VGA) input and a Digital Video Interface (DVI) input.

It can provide analogue and digital video signals and transmit video content at a signal capacity of 80MHz.

It has two rear USB 2.0 ports (Type A) and one USB Type B port with a current capacity of 500mA for connecting to host computers and other peripheral devices.

It has a DC power input rated at 9-36V DC using a DIN rail mounted AC power adapter.
April 11, 2025 BY
IN ABB

ABB IRB 1200 One of the new generation of 6-axis industrial robots

The IRB 1200 is one of the latest generation of 6-axis industrial robots from ABB Robotics with a payload of 5 to 7kg.

It is designed for manufacturing industries that use robot-based flexible automation, such as the 3C industry.

The robot’s open architecture makes it particularly suitable for flexible use and allows extensive communication with external systems.

IRB 1200 Type A

Type A – Axis Calibration

The difference between the IRB 1200 and the IRB 1200 Type A is that the Type A uses axis calibration. Each axis has a bushing on which the calibration tool is mounted.

Therefore, the castings of the IRB 1200 and IRB 1200 A models are different.

How do I know the type of robot?

The type label on the robot base indicates whether the robot is axis calibrated or not.

These robots are named IRB 1200 A models.

Robots that are not axis calibrated are simply named IRB 1200 (no type indicated).

IRB 1200 Type B

Type B – SafeMove 2

The IRB 1200 Type B differs from the other www.cniacs.com IRB 1200 versions in that

Type B supports SafeMove 2.

Therefore, the following components differ from the other versions:

– Base

1.1.1 Construction

Continued

– Drive unit, shaft 2. shaft 3. shaft 5 and shaft 6

– Motor with pulley, shaft 4 and shaft 5

– Robot cable harness

– Battery pack

– SMB unit (replaces EIB unit)
April 11, 2025 BY
IN A-B

A-B 6180P-15BPXPDC Display Computer

Description

The 6180P-15BPXPDC display computer is an Allen-Bradley/Rockwell Automation VersaView display computer.

Uses DC power: The 6180P-15BPXPDC display computer is an Allen-Bradley/Rockwell Automation VersaView display computer that uses DC power.

It operates on a range of 18 to 32 volts D.C. The 6180P-15BPXPDC display computer has a 15-inch wide screen that serves as both a display and a touch screen.

The 6180P-15BPXPDC display computer screen is 15 inches wide and serves as both a display and a touch screen. The screen supports full colour graphics.

The 6180P-15BPXPDC display computer also has a keypad for control with the touch screen.

The Allen-Bradley 6180P-15BPXPDC is a VersaView Plus integrated display computer with a keypad and touchscreen.

The computer can be used as an industrial computer or operator input station. It has a 15-inch touchscreen colour active matrix thin film transistor display.

The display area is 12 x 9 inches with a native resolution of 1024 x 768. The display has a response time of 20 milliseconds and can be fitted with an anti-glare cover.

The computer has a horizontal viewing angle of 60Ëš and a vertical viewing angle of 40Ëš. The 6180P-15BPXPDC computer provides 44 function keys.

The entire computer measures approximately 13.97 x 19.01 x 8.86 inches and weighs approximately 38.8 pounds.

The computer has an Intel 945GME system chipset, dual-channel DDR II memory slots, and two DIMM slots.

Up to 2 GB of memory can be installed in each slot, with a maximum of 4 GB of system memory.

It also comes with 1 full-length ISA expansion slot, 2 full-length slots and 1 half-length slot, PCI 2.2. 5V I/O PCI expansion slot.

The 6180P-15BPXPDC features a hot-swappable 3.5-inch SATA-interface 160 GB hard drive and a slim DVD-RW drive.

Available audio jacks include a microphone in jack, line in jack, and line out jack.

The 6180P-15BPXPDC computer also offers multiple input/output ports, including a parallel port, two serial ports, and a DVI port,

4 rear USB ports and 2 front USB ports. The computer also has 2 RJ45 Ethernet LAN ports at 10/100/1000 Mbps.

The cooling system includes a PSU fan, 2 chassis fans, and a processor cooler.

The computer also features Caps Lock, Numeric Lock, Power/Standby and HDD/ODD/FDD activity status indicators.

The 6180P-15BPXPDC has an input voltage of www.cniacs.com 18-32V DC and a peak inrush current of 20 A at 24V for 5 ms.

It has a power dissipation of 144 W and a power consumption of 144 W (8 A at 18V DC, 4.5 A at 32V DC).

Note that the computer has ACPI-compliant power management. The operating temperature range is 0-55 ËšC, the storage temperature range is -20-60 ËšC.

The non-condensing relative humidity is 20-85% during operation and 5-90% during non-operation.

The 6180P-15BPXPDC has an operating vibration peak of 1g and a non-operating vibration peak of 2g; an operating shock of 15g and a non-operating shock of 30g.

6180P-15BPXPDC Technical Description

The VersaView Plus series is equipped with a 15″ colour display and keypad/touchscreen. Colour display, keypad/touchscreen inputs and 18V-32V DC power supply.

Menu

Search for products

Back to Top
Product has been added to your cart