Category: Bachmann

Modern automation solutions are highly dependent on pre

cise, fast and robust sensors with an analog interface. The

wide range of interfaces required for integration can be

challenging here. This is especially the case when a large

number of different interfaces requires a correspondingly

large variety of types of acquisition modules.

This is a challenge that the AIM112 type modules meet very

easily. Up to 12 analog inputs can be individually config

ured to the desired signal type. The modules provide both

the common standard signals for current loops (4 mA to

20 mA, ±20 mA) and 4 high-impedance voltage measuring

ranges (±10 V to ±10 mV), each adapted to the conversion

range. Alternatively, channel types for all industrially rele

vant thermocouples including integrated characteristic lin

earization are available for measuring very wide tempera

ture ranges.

Precise signal conversion is possible with a 16‑bit resolu

tion and at very high sampling rates thanks to the special

measurement electronics. Widely adjustable filter chains,

precisely tuned to the signal path, ensure a configurable

balance between interference suppression and measure

ment dynamics. A hardware-accelerated high-speed inter

polation that can be activated as required provides contin

uous measurement signals independent of the filter set

tings and even with very short bus cycles.

Features

● 12 channel analog input module

● Channel-by-channel configurable signal type

● Temperature measurement:

Thermocouple types J, K, T, N, E, R, S, B

● Voltage measurement ±10 V, ±1 V, ±100 mV, ±10 mV

● Current input ±20 mA, 4 mA to 20 mA

● Value range and measured value monitoring

● Synchronous clocks / latch

Features

● 16-channel analog input/output module

● Configurable by channel: signal type and direction

● Pt100/Pt1000 2-wire temperature measurement

● Current output 4 mA to 20 mA, 0 mA to 20 mA, 0 mA to

2 mA, 0 µA to 200 µA

● Value range and measured value monitoring

● Synchronous clocks / latch

Temperature measurements represent the numerically

largest group of analog interfaces in industrial automa

tion. All the more reason why technical perfection and

cost-effectiveness are important requirements here. The

AIO116 module types cover both of these requirements in

an exemplary manner. Up to 16 Pt100/Pt1000 sensors can

be cost-effectively connected to a single module using a

2‑wire connection technology.

Temperature measurements represent the numerically

largest group of analog interfaces in industrial automa

tion. All the more reason why technical perfection and

cost-effectiveness are important requirements here. The

AIO116 module types cover both of these requirements in

an exemplary manner. Up to 16 Pt100/Pt1000 sensors can

be cost-effectively connected to a single module using a

2‑wire connection technology.

The temperature is recorded with 16‑bit resolution and,

thanks to special measuring electronics, with very high

sampling rates. Widely adjustable filter chains, precisely

tuned to the signal path, ensure a configurable bal

ance between interference suppression and measurement

dynamics. A hardware-accelerated high-speed interpolation

that can be activated as required provides continuous

measurement signals independent of the filter settings and

even with very short bus cycles. Alternatively, each indi

vidual channel can also be operated as a 14 bit current

output (4 mA to 20 mA, 0 mA to 20 mA).

Features

● 12-channel analog input/output module

● Configurable by channel: signal type and direction

● Pt100/Pt1000 2-wire temperature measurement

● Current output 4 mA to 20 mA, 0 mA to 20 mA,

0 mA to 2 mA, 0 µA to 200 µA

● Value range and measured value monitoring

● Synchronous clocks / latch

Temperature measurements represent the numerically

largest group of analog interfaces in industrial automa

tion. All the more reason why technical perfection and

cost-effectiveness are important requirements here. The

AIO112 module types cover both of these requirements in

an exemplary manner. Up to 12 Pt100/Pt1000 sensors can

be cost-effectively connected to a single module using a

2‑wire connection technology.

The temperature is recorded with 16‑bit resolution and,

thanks to special measuring electronics, with very high

sampling rates. Widely adjustable filter chains, precisely

tuned to the signal path, ensure a configurable bal

ance between interference suppression and measurement

dynamics. A hardware-accelerated high-speed interpolation

that can be activated as required provides continuous

measurement signals independent of the filter settings and

even with very short bus cycles. Alternatively, each indi

vidual channel can also be operated as a 14 bit current

output (4 mA to 20 mA, 0 mA to 20 mA).

Plants extended over large distances, interference fields

caused by power engineering systems, difficult grounding

conditions or aggressive substances close to the measure

ment sensors the challenges in analog measurement tech

nology for industrial applications can be manifold.

Floating measurement circuits with differential circuits

must be planned in order to exclude interference from

the measurement chain as much as possible. To prevent

interference and damage from being transmitted from one

sensor circuit to all the others, the measuring and control

circuits are galvanically isolated from each other.

For this purpose, the AIO104/I module type offers the ben

efits of an extremely versatile multi-signal analog input/

output module combined with channel-wise galvanic isola

tion. Each of the 4 primary channels can be operated indi

vidually either as an analog input or output. The spectrum

of the inputs ranges from current loops (4 mA to 20 mA,

±20 mA) to 4 high-impedance voltage measurement ranges

(±10 V to ±10 mV), Pt100/Pt1000 temperature measure

ment in 2-wire, 3-wire, and 4-wire connection technology as

well as thermocouples, and through to freely configurable

resistance measurement. The integrated measuring range

and measured value monitoring enable both sensor circuit

faults as well as process alarms to be implemented easily.

Current loops can also be driven or 0 V to 10 V, ±10 V

voltage signals can be output in 14 bits. Besides the 4 freely

configurable primary channels, up to 4 additional I/O chan

nels with restricted signal types are available.

Features

● 4-channel analog input/output module isolated

● Up to 4 additional analog channels depending on the

required signal type

● Configurable by channel: signal type and direction

● AI current/voltage, Pt100. Pt1000. thermocouples (J, K, T,

N, E, R, S, B)

● AO current/voltage

● Channel-wise galvanic isolation

● Oversampling

● Synchronous clocks

The cost and performance optimized design of complex

automation solutions involves a large number of different

sensor and actuator types. The standard 10 V and 4 mA

to 20 mA interfaces are often not sufficient to achieve

demanding objectives.

With the UIO108. a single module type covers all common

analog and digital signals for inputs and outputs that can

be configured individually for each channel. The extensive

versatility of the module is rounded off by a wide range

of additional functions such as counters, encoders, pulse

width modulation and the control of a stepper motor

driver. This simplifies the entire process from the quotation

phase through planning, programming and commissioning,

right up to stockkeeping and servicing. Besides the 8 freely

configurable primary channels, up to 8 additional I/O chan

nels with restricted signal types are available.

Features

● 8-channel analog/digital input/output module

● Up to 8 additional channels depending on the required

signal type

● Configurable by channel: signal type and direction

● DI / counter / encoder

● DO / PWM

● AI current/voltage, Pt100. Pt1000. thermocouples (J, K, T, N, E, R, S, B)

● AO current/voltage

● Control of a stepper motor driver

● Synchronous clocks / latch / sync out

● Oversampling

● Direct module-to-module communication